|
| MXD2020ML |
|
||
|
ETC |
|
1 page
MEMSIC MXD2020GL/ML Page 1 of 7 2002.08.29.1 Improved, Ultra Low Noise ±1 g Dual Axis Accelerometer with Digital Outputs MXD2020GL/HL MXD2020ML/NL FEATURES Resolution better than 1 milli-g Dual axis accelerometer fabricated on a monolithic CMOS IC On chip mixed mode signal processing No moving parts 50,000 g shock survival rating 17 Hz bandwidth expandable to >160 Hz 3.0V to 5.25V single supply continuous operation Continuous self test Independent axis programmability (special order) Compensated for Sensitivity over temperature Ultra low initial Zero-g Offset APPLICATIONS Automotive – Vehicle Security/Vehicle stability control/ Headlight Angle Control/Tilt Sensing Security – Gas Line/Elevator/Fatigue Sensing Information Appliances – Computer Peripherals/PDA’s/Mouse Smart Pens/Cell Phones Internal Oscillator Sck (optional) CLK Heater Control X axis Y axis Factory Adjust Offset & Gain LPF LPF Temperature Sensor Voltage Reference Vref Dout X Vdd Vda Gnd 2-AXIS SENSOR Dout Y Tout Continous Self Test A/D A/D MXD2020GL/HL/ML/NL FUNCTIONAL BLOCK DIAGRAM Gaming – Joystick/RF Interface/Menu Selection/Tilt Sensing GPS – electronic Compass tilt Correction Consumer – LCD projectors, pedometers, blood pressure Monitor, digital cameras GENERAL DESCRIPTION The MXD2020GL/HL/ML/NL is a low cost, dual axis accelerometer fabricated on a standard, submicron CMOS process. It is a complete sensing system with on-chip mixed mode signal processing. The MXD2020GL/HL/ML/NL measures acceleration with a full-scale range of ±1 g and a sensitivity of 20%/g. It can measure both dynamic acceleration (e.g. vibration) and static acceleration (e.g. gravity). The MXD2020GL/HL/ML/NL design is based on heat convection and requires no solid proof mass. This eliminates stiction and particle problems associated with competitive devices and provides shock survival of 50,000 g, leading to significantly lower failure rate and lower loss due to handling during assembly. The MXD2020GL/HL/ML/NL provides two digital outputs that are set to 50% duty cycle at zero g acceleration. The outputs are digital with duty cycles (ratio of pulse width to period) that are proportional to acceleration. The duty cycle outputs can be directly interfaced to a micro- processor. The typical noise floor is 0.2 mg/ Hz allowing signals below 1 milli-g to be resolved at 1 Hz bandwidth. The MXD2020GL/HL/ML/NL is packaged in a hermetically sealed LCC surface mount package (5 mm x 5 mm x 2 mm height) and is operational over a -40°C to 105°C(M/NL) and 0 °C to 70°C(G/HL) temperature range. Information furnished by MEMSIC is believed to be accurate and reliable. However, no responsibility is assumed by MEMSIC for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of MEMSIC. MEMSIC, Inc. 800 Turnpike St., Suite 202, North Andover, MA 01845 Tel: 978.738.0900 Fax: 978.738.0196 www.memsic.com |
|
링크 URL |
Alldatasheet 제휴사 |
|
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인 정보 보호 정책 | 즐겨찾기 | 링크교환 | 제조사별 검색 All Rights Reserved© Alldatasheet.com 2003 - 2012 |
| Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com | Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl |