ES25P80-75IC2T datasheet(7/35 Pages) EXCELSEMI

부품명	ES25P80-75IC2T

상세설명	8Mbit CMOS 3.0 Volt Flash Memory with 75Mhz SPI Bus Interface

Download	35 Pages

Scroll/Zoom	100%

제조업체	EXCELSEMI [Excel Semiconductor Inc.]

홈페이지

Logo

7 / 35 page

ES I

7

Rev. 0D May, 11, 2006

ES25P80

Excel Semiconductor inc.

ADVANCED INFORMATION

Protection Modes

The SPI memory device boasts the following data

protection mechanisms

1) All instructions that modify data must be preceded

by a Write Enable(WREN) instruction to set the

Write Enable Latch (WEL) bit. This bit is returned to

its reset state by the following events :

- Power-up

- WRDI instruction completion

- WRSR instruction completion

- PP instruction completion

- SE instruction completion

- BE instruction completion

2) The Block Protect (BP2, BP1, BP0) bits allow part

of the memory to be configured as read-only. This is

the Software Protected Mode (SPM).

3) The Write Protect (W#) signal works in coopera-

tion with the Status Register Write Disable (SRWD)

bit to enable write-protection. This is the Hardware

Protected Mode (HPM).

4) Program, Erase and Write Status Register instruc-

tions are checked to verify that they consist of a

number of clock pulses that is a multiple of eight,

before they are accepted for execution.

If the falling edge does not coincide with Serial Clock

(SCK) being Low, the Hold condition starts after

Serial Clock (SCK) next goes Low. Similarly, If the

rising edge does not coincide with Serial Clock

(SCK) being Low, the Hold condition ends after

Serial Clock (SCK) next goes Low (Figure 3).

During the Hold condition, the Serial Data Output

(SO) is high impedance, and Serial Data Input (SI)

and Serial Clock (SCK) are Don’t Care.

Normally, the device remains selected, with Chip

Select (CS#) driven Low, for the entire duration of

the Hold condition. This ensures that the state of the

internal logic remains unchanged from the moment

of entering the Hold condition.

If Chip Select (CS#) goes High while the device is in

the Hold condition, this has the effect of resetting the

internal logic of the device. To restart communication

with the device, it is necessary to drive Hold

(HOLD#) High, and then to drive Chip Select (CS#)

Low. This prevents the device from going back to the

Hold condition.

Table 1. Protected Area Sizes

Protected Memory

Area (Top Level)

Status Register Content

Memory Content

BP2 Bit

BP1 Bit

BP0 Bit

Protected Area

Unprotected Area

0

none

00000 ~ FFFFF

1 / 16

0

1

F0000 ~ FFFFF

00000 ~ EFFFF

1 / 8

0

1

0

E0000 ~ FFFFF

00000 ~ DFFFF

1 / 4

0

1

C0000 ~ FFFFF

00000 ~ BFFFF

1 / 2

1

0

80000 ~ FFFFF

00000 ~ 7FFFF

All

1

0

1

00000 ~ FFFFF

+ parameter page

none

All

1

0

00000 ~ FFFFF

+ parameter page

none

All

1

00000 ~ FFFFF

+ parameter page

none

유사한 부품 번호 - ES25P80-75IC2T

제조업체	부품명	데이터시트	상세설명
Excel Semiconductor Inc...	ES25P16	435Kb / 35P	16Mbit CMOS 3.0 Volt Flash Memory with 75Mhz SPI Bus Interface
Excel Semiconductor Inc...	ES25P40	435Kb / 35P	4Mbit CMOS 3.0 Volt Flash Memory with 75Mhz SPI Bus Interface

More results

유사한 설명 - ES25P80-75IC2T

제조업체	부품명	데이터시트	상세설명
Excel Semiconductor Inc...	ES25P40	435Kb / 35P	4Mbit CMOS 3.0 Volt Flash Memory with 75Mhz SPI Bus Interface
Excel Semiconductor Inc...	ES25P16	435Kb / 35P	16Mbit CMOS 3.0 Volt Flash Memory with 75Mhz SPI Bus Interface
SPANSION	S25FL004A	945Kb / 39P	4-Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
	S25FL004D	724Kb / 36P	4 Megabit CMOS 3.0 Volt Flash Memory with 50 Mhz SPI Bus Interface
	S25FL064A	949Kb / 32P	64 Megabit CMOS 3.0 Volt Flash Memory with 50MHz SPI (Serial Peripheral Interface) Bus
	S25FL032A	941Kb / 36P	32 Megabit CMOS 3.0 Volt Flash Memory with 50MHz SPI (Serial Peripheral Interface) Bus
	S25FL016A	997Kb / 34P	16 Megabit CMOS 3.0 Volt Flash Memory with 50MHz SPI (Serial Peripheral Interface) Bus
	S25FL128P	1Mb / 48P	128 Megabit CMOS 3.0 Volt Flash Memory with 104-MHz SPI (Serial Peripheral Interface) Bus
	S25FL016A	1Mb / 36P	16 Megabit CMOS 3.0 Volt Flash Memory with 50-MHz SPI (Serial Peripheral Interface) Bus
	S25FL008A	960Kb / 32P	8-Megabit CMOS 3.0 Volt Flash Memory with 50 MHz SPI (Serial Peripheral Interface) Bus

More results

ES25P80-75IC2T 데이터시트(PDF) 7 Page - Excel Semiconductor Inc.

ES25P80-75IC2T 데이터시트(HTML) 7 Page - Excel Semiconductor Inc.

유사한 부품 번호 - ES25P80-75IC2T

유사한 설명 - ES25P80-75IC2T

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35

데이터시트 다운로드

링크 URL