전자부품 데이터시트 검색엔진 |
|
CX74063-34 데이터시트(PDF) 8 Page - Skyworks Solutions Inc. |
|
CX74063-34 데이터시트(HTML) 8 Page - Skyworks Solutions Inc. |
8 / 62 page Data Sheet I CX74063-34/-35/-36 8 Skyworks Solutions, Inc., Proprietary and Confidential NOVEMBER 25, 2003 [781] 376-3000 I FAX [781] 376-3100 I SALES@SKYWORKSINC.COM I WWW.SKYWORKSINC.COM 103116C Table 1. CX74063-3x Signal Descriptions (5 of 5) Pin # Name Description Equivalent Circuit 48 RXQN Receiver output Q negative 49 RXQP Receiver output Q positive 50 RXIN Receiver output I negative 51 RXIP Receiver output I positive 52 VCC4 Baseband supply VCC4 53 VCCTXVCO Transmit VCO supply VCCTXVCO 54 TX900 Low band transmit VCO 55 TX1800/TX1900 DCS and PCS transmit VCO output 56 TXVCOTUNE Transmit VCO control input Technical Description The CX74063-3x transceiver contains the following sections, as shown in Figure 2. • Receive section. Includes three integrated LNAs, a quadrature demodulator section that performs direct down conversion, baseband amplifier circuitry with I/Q outputs, and three stages of DC offset correction. The receiver can be calibrated to optimize IP2 performance. • Synthesizer section. Includes an integrated on-chip VCO locked by a fractional-N synthesizer loop, and a crystal oscillator to supply the reference frequency. • Transmit section. The TX path is a translational loop architecture consisting of an I/Q modulator, integrated high power VCOs, offset mixer, programmable divider, PFD, and charge pump. The device also provides integrated gain controller for the PAC loop, plus the bias generator for an external diode detector. A 3-wire serial interface controls the transceiver and synthesizer. The receiver gain control, as well as the division ratios and charge pump currents in the synthesizer and transmitter, can be programmed using 24-bit words. These 24-bit words are programmed using the 3-wire input signals CLK, DATA, and LE. To ensure that the data stays latched in power down mode, pin 43 (VDDBB) must be continuously supplied with voltage. This pin is provided for the digital sections to allow power supply operation compatible with modern digital baseband devices. The TXENA, RXENA, and SXENA signals separately enable the CX74063-3x transmitter, receiver, and synthesizer sections. TXENA and RXENA should be held low during programming. SXENA should be held high during the programming of the R3 IP2 Calibration Register. (These timing signals are detailed in Figures 9, 10, and 11.) |
유사한 부품 번호 - CX74063-34 |
|
유사한 설명 - CX74063-34 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |