전자부품 데이터시트 검색엔진 |
|
NUP2201MR6 데이터시트(PDF) 4 Page - ON Semiconductor |
|
NUP2201MR6 데이터시트(HTML) 4 Page - ON Semiconductor |
4 / 6 page NUP2201MR6 http://onsemi.com 4 VCC D1 D2 Data Line IESDpos IESDneg VF + VCC −VF IESDpos IESDneg Power Supply Protected Device Looking at the figure above, it can be seen that when a positive ESD condition occurs, diode D1 will be forward biased while diode D2 will be forward biased when a negative ESD condition occurs. For slower transient conditions, this system may be approximated as follows: For positive pulse conditions: Vc = Vcc + VfD1 For negative pulse conditions: Vc = −VfD2 ESD events can have rise times on the order of some number of nanoseconds. Under these conditions, the effect of parasitic inductance must be considered. A pictorial representation of this is shown below. VCC D1 D2 Data Line IESDpos IESDneg VC = VCC + Vf + (L diESD/dt) IESDpos IESDneg Power Supply Protected Device VC = −Vf − (L diESD/dt) An approximation of the clamping voltage for these fast transients would be: For positive pulse conditions: Vc = Vcc + Vf + (L diESD/dt) For negative pulse conditions: Vc = −Vf – (L diESD/dt) As shown in the formulas, the clamping voltage (Vc) not only depends on the Vf of the steering diodes but also on the L diESD/dt factor. A relatively small trace inductance can result in hundreds of volts appearing on the supply rail. This endangers both the power supply and anything attached to that rail. This highlights the importance of good board layout. Taking care to minimize the effects of parasitic inductance will provide significant benefits in transient immunity. Even with good board layout, some disadvantages are still present when discrete diodes are used to suppress ESD events across datalines and the supply rail. Discrete diodes with good transient power capability will have larger die and therefore higher capacitance. This capacitance becomes problematic as transmission frequencies increase. Reducing capacitance generally requires reducing die size. These small die will have higher forward voltage characteristics at typical ESD transient current levels. This voltage combined with the smaller die can result in device failure. The ON Semiconductor NUP2201MR6 was developed to overcome the disadvantages encountered when using discrete diodes for ESD protection. This device integrates a TVS diode within a network of steering diodes. D1 D2 D3 D4 0 NUP2201MR6 Equivalent Circuit During an ESD condition, the ESD current will be driven to ground through the TVS diode as shown below. VCC D1 D2 Data Line IESDpos Power Supply Protected Device The resulting clamping voltage on the protected IC will be: Vc = VF + VTVS. The clamping voltage of the TVS diode is provided in Figure 4 and depends on the magnitude of the ESD current. The steering diodes are fast switching devices with unique forward voltage and low capacitance characteristics. |
유사한 부품 번호 - NUP2201MR6_06 |
|
유사한 설명 - NUP2201MR6_06 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |