전자부품 데이터시트 검색엔진 |
|
SST25WF010 데이터시트(PDF) 7 Page - Silicon Storage Technology, Inc |
|
SST25WF010 데이터시트(HTML) 7 Page - Silicon Storage Technology, Inc |
7 / 29 page Advance Information 512 Kbit / 1 Mbit / 2 Mbit 1.8V SPI Serial Flash SST25WF512 / SST25WF010 / SST25WF020 7 ©2006 Silicon Storage Technology, Inc. S71328-01-000 02/07 Status Register The software status register provides status on whether the flash memory array is available for any Read or Write oper- ation, whether the device is Write enabled, and the state of the Memory Write protection. During an internal Erase or Program operation, the status register may be read only to determine the completion of an operation in progress. Table 4 describes the function of each bit in the software status register. Busy The Busy bit determines whether there is an internal Erase or Program operation in progress. A ‘1’ for the Busy bit indi- cates the device is busy with an operation in progress. A ‘0’ indicates the device is ready for the next valid operation. Write Enable Latch (WEL) The Write-Enable-Latch bit indicates the status of the inter- nal Write-Enable-Latch memory. If the WEL bit is set to ‘1’, it indicates the device is Write enabled. If the bit is set to ‘0’ (reset), it indicates the device is not Write enabled and does not accept any Write (Program/Erase) commands. The Write-Enable-Latch bit is automatically reset under the following conditions: • Device Reset • Power-up • Write-Disable (WRDI) instruction completion • Byte-Program instruction completion • Auto Address Increment (AAI) programming is completed or reached its highest unprotected memory address • Sector-Erase instruction completion • Block-Erase instruction completion • Chip-Erase instruction completion • Write-Status-Register instructions Auto Address Increment (AAI) The Auto Address Increment Programming-Status bit pro- vides status on whether the device is in AAI programming mode or Byte-Program mode. The default at power up is Byte-Program mode. TABLE 4: Software Status Register Bit Name Function Default at Power-up Read/Write 0 BUSY 1 = Internal Write operation is in progress 0 = No internal Write operation is in progress 0R 1 WEL 1 = Device is memory Write enabled 0 = Device is not memory Write enabled 0R 2 BP0 Indicate current level of block write protection (See Table 5) 1 R/W 3 BP1 Indicate current level of block write protection (See Table 5) 1 R/W 4:5 RES Reserved for future use 0 N/A 6 AAI Auto Address Increment Programming status 1 = AAI programming mode 0 = Byte-Program mode 0R 7 BPL 1 = BP1 and BP0 are read-only bits 0 = BP1 and BP0 are read/writable 0R/W T4.1 1328 |
유사한 부품 번호 - SST25WF010 |
|
유사한 설명 - SST25WF010 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |