 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
4AV15F 데이터시트(PDF) 3 Page - Honeywell Solid State Electronics Center |
|
||||||||||||||||||||||||||||||
4AV15F 데이터시트(HTML) 3 Page - Honeywell Solid State Electronics Center |
|
|
3 / 4 page  4AV Series Vane Sensors ISSUE 2 PK 87605 For application help: call 1-800-537-6945 Honeywell • Sensing and Control 3 SOLDERING CAUTION PRODUCT DAMAGE • Ensure iron tip is clean when soldering. Failure to comply with these instructions may result in product damage. Hand Soldering The following is recommended: 1. Flux: Rosin Base 2. Solder: Kester #44 60-40 rosin core, or equivalent. 3. Soldering Iron: Type; Weller, Model TC-552, 55 watt or equivalent. 4. Tip Size: 3mm (.118 in.) Diameter x 30mm (1.182 in.) long 5. Tip Temperature: 288 °C (550°F) max 6. Terminal Contact Time: 6 seconds max. Wave Soldering The following is recommended: 1. Flux: London Chemical Co. Loncoflux - 106A35 or equivalent 2. Preheat: Preheaters should be set to give 95 °C (200 °F) on the top (component side) of printed circuit board just prior to board entering the wave. (May have to be adjusted depending upon board thickness.) 3. Solder Temperature: 260 °C (500 °F) max.; preferably 252 °C to 260 °C (485 °F to 500 °F). 4. Speed: Set conveyor speed to approximately 4.5 feet/minute (1,37 meters/minute). 5. Printed circuit board requires rigid support during wave soldering. CLEANING Hand Cleaning Clean areas with a 50-50 mixture of isopropyl alcohol and clean tap water. Dry in a 71 °C (160 °F) oven for 10-15 minutes, preferably in a non- circulating oven. This will remove all moisture from the assembly, which must be done before electrical testing, or application. Machine Cleaning * Detergent: London Chemical Company Loncoterge 444-NRT6 or equivalent. Equipment: Dee Electric Aqueous Cleaner or equivalent. The following is reccommended: 1. Wash Section: 55 °C (130 °F) maximum water temperature, 5 to 10% maximum solution soft water, low pressure nozzles (60 psi) on top spray and high pressure nozzles (120 psi) on bottom spray, conveyor speed 3 feet/minute minimum. Recirculating tank. 2. Rinse Section #1: Clean tap water up to 25 grains hard, salt free (to minimize possibility of corrosion), unheated, non-recirculating, with high pressure nozzles (120 psi). 3. Rinse Section #2: Clean deionized water only, high pressure nozzles (120 psi), unheated and non-recirculating. 4. Air Knife Section: To remove excessive amounts of water. 5. Drying Section: 71 °C (160 °F) drying for 10-15 minutes, preferably in a non-circulating conveyor oven. * In this cleaning system, the detergent in the wash section removes the non-polar contaminants, the first rinse removes the detergent solution, and the deionized water rinse removes the polar contaminants. The air knife and dryer remove all the moisture from the assembly, which must be done before electrical testing or application. CAUTION PRODUCT DAMAGE • Ensure cleaner does not come in contact with sensor If other cleaning methods are selected for removal of flux residue. Failure to comply with these instructions may result in product damage. |
유사한 부품 번호 - 4AV15F |
|
유사한 설명 - 4AV15F |
|
|
|
링크 URL |
| 개인정보취급방침 |
| ALLDATASHEET.CO.KR |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
