전자부품 데이터시트 검색엔진 |
|
LM134D 데이터시트(PDF) 6 Page - STMicroelectronics |
|
LM134D 데이터시트(HTML) 6 Page - STMicroelectronics |
6 / 16 page Application information LM134-LM234-LM334 6/16 4 Application information 4.1 Slew rate At slew rates above a threshold (see Figure 4 and Figure 5), the LM134, LM234, LM334 can have a non-linear current characteristic. The slew rate at which this takes place is directly proportional to Iset. At Iset = 10µA, dv/dt max. = 0.01V/µs ; at Iset = 1mA, dv/dt max. = 1V/µs. Slew rates of more than 1V/µs do not damage the circuit nor do they produce high currents. 4.2 Thermal effects Internal heating can have a significant effect on current regulation for an Iset above 100µA. For example, each increase of 1V in the voltage across the LM134 at Iset = 1mA will increase the junction temperature by ≈ 0.4°C (in still air). The output current (Iset) has a temperature coefficient of about 0.33%/°C. Thus the change in current due to the increase in temperature will be (0.4) (0.33) = 0.132%. This is a degradation of 10 : 1 in regulation versus the true electrical effects. Thermal effects should be taken into account when d.c. regulation is critical and Iset is higher than 100µA. 4.3 Shunt capacitance In certain applications, the 15pF value for the shunt capacitance should be reduced: ● because of loading problems, ● because of limitation of output impedance of the current source in a.c. applications. You can easily reduce the capacitance by adding a FET as shown in Typical applications on page 8. The value of this capacitance can be reduced by at least 3pF and regulation can be improved by an order of magnitude without any modifications of the d.c. characteristics (except for the minimum input voltage). 4.4 Noise The current noise produced by LM134, LM234, and LM334 is about 4 times that of a transistor. If the LM134, LM234, LM334 is used as an active load for a transistor amplifier, the noise at the input will increase by about 12dB. In most cases this is acceptable, and a single amplifier can be built with a voltage gain higher than 2000. 4.5 Lead resistance The sense voltage which determines the current of the LM134, LM234, LM334 is less than 100mV. At this level, the thermocouple effects and the connection resistance should be reduced by locating the current setting resistor close to the device. Do not use sockets for the ICs. A contact resistance of 0.7 Ωis sufficient to decrease the output current by 1% at the 1mA level. |
유사한 부품 번호 - LM134D |
|
유사한 설명 - LM134D |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |