전자부품 데이터시트 검색엔진 |
|
AD23602C 데이터시트(PDF) 2 Page - MicroPower Direct, LLC |
|
AD23602C 데이터시트(HTML) 2 Page - MicroPower Direct, LLC |
2 / 2 page Derating Curve Model Selection Guide Mechanical Dimensions Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) MicroPower Direct www.micropowerdirect.com 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com Model Number Rated Power (W) Input Output Overvoltage Protection (VDC) Ripple & Noise (mV p-p) Efficiency (%, Typ) Voltage (VAC) Current (A) Voltage (VDC) Current (A) Max) Current (A) Range Universal Range 115 VAC 230 VAC AD23601C 360 100 - 240 1.0 0.5 +12 (V1) 28.0 0 ~ 28.0 14 ~ 16 100 78 +5 (V2) 3.0 0 ~ 3.0 N/A 50 AD23602C 360 100 - 240 1.0 0.5 +24 (V1) 14.0 0 ~ 14.0 27 ~ 30 150 80 +5 (V2) 3.0 0 ~ 3.0 N/A 50 AD23603C 360 100 - 240 1.0 0.5 48 (V1) 7.0 0 ~ 7.0 52 ~ 56 250 80 +5 (V2) 3.0 0 ~ 3.0 N/A 50 Notes: 1. Load regulation is specified for a load change of 20% to 100%. For models AD23601C, load regulation for V1 (12V) is ±2% 2. Ripple & noise is measured using equipment with 20 Mhz of bandwidth with the unit under test operating at rated load and a 110 VAC input. Connection to the unit is made with a 0.1 μF / 630V metalized capacitor & a 47 μF electrolytic capacitor connected in parallel. 3. Transient recovery is measured to within a 1% error band for a load step change of 50% to 100%. 4. Isolation resistance is given for Input/Output and Input/FG. For Output/FG., it is 50 M Ω 5. Overload protection is power limiting. The unit recovers automatically when the fault is removed. 6. Over voltage protection is a shut down type. The unit recovers automatically when the fault is removed. 7. To mount the unit to the DIN rail, tilt the unit rearwards from the top, fitting the mount over the top of the rail. Press back on the bottom front of the unit until it locks in place on the rail. To remove the unit from the rail, pull the removal clip at the bottom rear of the unit downward with a screw driver. With the clip down, lift up on the unit from the bottom front until it clears the rail. Before installation or removal all wiring should be disconnected and the main power to the system shut off. 8. When wiring the supply, all lines should be as thick and short as possible. AWG 14 wire is recom- mended for the AD2360C series. 9. The units should be mounted so they are vertically orientated. Air flow (if provided) would optimally flow from the bottom to the top of the unit. 10. It is recommended that a fuse be used on the input of a power supply for protection. For the AD2360C series a 250VAC 5.0A is recom- mended. Connections TB 1 Pin Function 1 FT (Optional) 2 FT (Optional) 3+V2 (5V) Output 4 Output Common 5 Output Common 6+V1 Output 7+V1 Output Connections TB 2 Pin Function 1 AC Input - Live 2 AC Input - Neutral 3 Frame Ground (FG Units with the optional “FT” outputs may be easily connected for “Fault Tolerant operation. Contact the factory for details |
유사한 부품 번호 - AD23602C |
|
유사한 설명 - AD23602C |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |