전자부품 데이터시트 검색엔진 |
|
SST25VF020B-80-4I-QAE 데이터시트(PDF) 7 Page - Silicon Storage Technology, Inc |
|
SST25VF020B-80-4I-QAE 데이터시트(HTML) 7 Page - Silicon Storage Technology, Inc |
7 / 33 page Data Sheet 2 Mbit SPI Serial Flash SST25VF020B 7 ©2010 Silicon Storage Technology, Inc. S71417-02-000 04/10 • Power-up • Write-Disable (WRDI) instruction completion • Byte-Program instruction completion • Auto Address Increment (AAI) programming is completed or reached its highest unprotected memory address • Sector-Erase instruction completion • Block-Erase instruction completion • Chip-Erase instruction completion • Write-Status-Register instructions Auto Address Increment (AAI) The Auto Address Increment Programming-Status bit pro- vides status on whether the device is in AAI programming mode or Byte-Program mode. The default at power up is Byte-Program mode. Block Protection (BP1, BP0) The Block-Protection (BP1, BP0) bits define the size of the memory area, as defined in Table 5, to be software pro- tected against any memory Write (Program or Erase) operation. The Write-Status-Register (WRSR) instruction is used to program the BP1 and BP0 bits as long as WP# is high or the Block-Protect-Lock (BPL) bit is 0. Chip-Erase can only be executed if Block-Protection bits are all 0. After power-up, BP1 and BP0 are set to 1. Block Protection Lock-Down (BPL) WP# pin driven low (VIL), enables the Block-Protection- Lock-Down (BPL) bit. When BPL is set to 1, it prevents any further alteration of the BPL, BP1, and BP0 bits of the sta- tus register and BSP and TSP of Status Register 1. When the WP# pin is driven high (VIH), the BPL bit has no effect and its value is “Don’t Care”. After power-up, the BPL bit is reset to 0. Top-Sector Protection/Bottom-Sector Protection The Top-Sector Protection (TSP) and Bottom-Sector Pro- tection (BSP) bits independently indicate whether the high- est and lowest sector locations are Write locked or Write accessible. When TSP or BSP is set to ‘1’, the respective sector is Write locked; when set to ‘0’ the respective sector is Write accessible. If TSP or BSP is set to '1' and if the top or bottom sector is within the boundary of the target address range of the program or erase instruction, the initi- ated instruction (Byte-Program, AAI-Word Program, Sec- tor-Erase, Block-Erase, and Chip-Erase) will not be executed. Upon power-up, the TSP and BSP bits are auto- matically reset to ‘0’. TABLE 5: Software Status Register Block Protection FOR SST25VF020B1 1. X = Don’t Care (RESERVED) default is “0 Protection Level Status Register Bit2 2. Default at power-up for BP1 and BP0 is ‘11’. (All Blocks Protected) Protected Memory Address BP1 BP0 2 Mbit 00 0 None 1 (1/4 Memory Array) 0 1 030000H-03FFFFH 1 (1/2 Memory Array) 1 0 020000H-03FFFFH 1 (Full Memory Array) 1 1 000000H-03FFFFH T5.0 1417 |
유사한 부품 번호 - SST25VF020B-80-4I-QAE |
|
유사한 설명 - SST25VF020B-80-4I-QAE |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |