전자부품 데이터시트 검색엔진 |
|
LC321664AM 데이터시트(PDF) 7 Page - Sanyo Semicon Device |
|
LC321664AM 데이터시트(HTML) 7 Page - Sanyo Semicon Device |
7 / 30 page LC321664AJ, AM, AT-80 No. 4795-7/30 Notes: 6) After the power is turned on, 200 µs are required after the arrival of VCC stabilized current before memory is initialized and begins operation. In addition, before memory operation initializes, approximately 8 cycles worth of RAS dummy cycles are required. When the on-chip refresh counter is applied, approximately 8-cycles worth of CAS-before-RAS dummy cycles are required instead of the RAS dummy cycles. 7) Measured at tT = 5 ns. 8) When measuring input signal timing, VIH (min) and VIL (max) are used for reference points. In addition, rise and fall time are defined between VIH and VIL. 9) Measured using an equivalent of 50 pF and one standard TTL load. 10) tOFF (max) and tOEZ (max) are defined as the time until output voltage can no longer be measured when output switches to a high impedance condition. 11) Operation is guaranteed if either tRRH or tRCH are satisfied. 12) These parameters are measured from the falling edge of CAS for an early-write cycle, and from the falling edge of UW and LW for a read-write/read-modify-write cycle. 13) tWCS, tCWD, tRWD, tAWD and tCPWD are not restrictive operating parameters for memory in that they specify the operating mode. If tWCS ≥ tWCS (min), the cycle switches to an early-write cycle and output pins switch to high impedance throughout the cycle. If tCWD ≥ tCWD (min), tRWD ≥ tRWD (min), tAWD ≥ tAWD (min) and tCPWD ≥ tCPWD (min), the cycle switches to a read-write/read-modify-write cycle and data outputs equal information in the selected cells. If neither of the above conditions are satisfied, output pins are in an undefined state. 14) tRCD (max) does not indicate a restrictive operating parameter but instead represents the point at which the access time tRAC (max) is guaranteed. If tRCD ≥ tRCD (max), access time is determined according to tCAC. 15) tRAD (max) does not indicate a restrictive operating parameter but instead represents the point at which the access time tRAC (max) is guaranteed. If tRAD ≥ tRAD (max), access time is determined according to tAA. 16) Operation is guaranteed if either tDZC or tDZO are satisfied. |
유사한 부품 번호 - LC321664AM |
|
유사한 설명 - LC321664AM |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |