전자부품 데이터시트 검색엔진 |
|
SST48CF256 데이터시트(PDF) 11 Page - Silicon Storage Technology, Inc |
|
SST48CF256 데이터시트(HTML) 11 Page - Silicon Storage Technology, Inc |
11 / 60 page Data Sheet CompactFlash Card SST48CF008 / 016 / 024 / 032 / 048 / 064 / 096 / 128 / 192 / 256 11 ©2001 Silicon Storage Technology, Inc. S71125-03-000 9/01 375 -OE (PC Card Memory Mode) I 9 This is an Output Enable strobe generated by the host interface. It is used to read data from the CompactFlash card in Memory Mode and to read the CIS and configuration registers. -OE (PC Card I/O Mode) In PC Card I/O Mode, this signal is used to read the CIS and configu- ration registers. -ATA SEL (True IDE Mode) To enable True IDE Mode this input should be grounded by the host. RDY/-BSY PC Card Memory Mode) O 37 In Memory Mode this signal is set high when the CompactFlash Card is ready to accept a new data transfer operation and held low when the card is busy. The Host memory card socket must provide a pull- up resistor. At power up and at Reset, the RDY/-BSY signal is held low (busy) until the CompactFlash card has completed its power up or reset function. No access of any type should be made to the Compact- Flash card during this time. The RDY/-BSY signal is held high (dis- abled from being busy) whenever the following condition is true: The CompactFlash Card has been powered up with +RESET continu- ously disconnected or asserted. -IREQ PC Card I/O Mode) I/O Operation - After the CompactFlash card has been configured for I/O operation, this signal is used as -Interrupt Request. This line is strobed low to generate a pulse mode interrupt or held low for a level mode interrupt. INTRQ (True IDE Mode) In True IDE Mode signal is the active high Interrupt Request to the host. -REG (PC Card Memory Mode) I 44 This signal is used during Memory Cycles to distinguish between Common Memory and Register (Attribute) Memory Attribute Memory Select accesses. High for Common Memory, Low for Attribute Mem- ory. -REG PC Card I/O Mode) The signal must also be active (low) during I/O Cycles when the I/O address is on the Bus. -REG (True IDE Mode) In True IDE Mode this input signal is not used and should be con- nected to VDD by the host. RESET (PC Card Memory Mode) I 41 When the pin is high, this signal Resets the CompactFlash Card. The CompactFlash card is Reset only at power up if this pin is left high or open from power-up. The CompactFlash card is also Reset when the Soft Reset bit in the Card Configuration Option Register is set. RESET (PC Card I/O Mode) This signal is the same as the PC Card Memory Mode signal. -RESET (True IDE Mode) In the True IDE Mode this input pin is the active low hardware reset from the host. VDD (PC Card Memory Mode) - 13,38 +5.0V, +3.3V power. VDD (PC Card I/O Mode) This signal is the same for all modes. VDD (True IDE Mode) This signal is the same for all modes. TABLE 2-2: SIGNAL DESCRIPTION (CONTINUED) (3 OF 4) Symbol Type1 Pin Name and Functions |
유사한 부품 번호 - SST48CF256 |
|
유사한 설명 - SST48CF256 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |