전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

AD7890AN-4 데이터시트(PDF) 10 Page - Analog Devices

부품명 AD7890AN-4
상세설명  LC2MOS 8-Channel, 12-Bit Serial, Data Acquisition System
Download  20 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  AD [Analog Devices]
홈페이지  http://www.analog.com
Logo AD - Analog Devices

AD7890AN-4 데이터시트(HTML) 10 Page - Analog Devices

Back Button AD7890AN-4 Datasheet HTML 6Page - Analog Devices AD7890AN-4 Datasheet HTML 7Page - Analog Devices AD7890AN-4 Datasheet HTML 8Page - Analog Devices AD7890AN-4 Datasheet HTML 9Page - Analog Devices AD7890AN-4 Datasheet HTML 10Page - Analog Devices AD7890AN-4 Datasheet HTML 11Page - Analog Devices AD7890AN-4 Datasheet HTML 12Page - Analog Devices AD7890AN-4 Datasheet HTML 13Page - Analog Devices AD7890AN-4 Datasheet HTML 14Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 10 / 20 page
background image
AD7890
–10–
REV. A
If the application requires a reference with a tighter tolerance or
the AD7890 needs to be used with a system reference, then the
user has the option of connecting an external reference to this
REF OUT/REF IN pin. The external reference will effectively
overdrive the internal reference and thus provide the reference
source for the ADC. The reference input is buffered but has a
nominal 2 k
Ω resistor connected to the AD7890’s internal refer-
ence. Suitable reference sources for the AD7890 include the
AD680, AD780 and REF-43 precision +2.5 V references.
Timing and Control Section
The AD7890 is capable of two interface modes, selected by the
SMODE input. The first of these is a self-clocking mode where the
part provides the frame sync, serial clock and serial data at the end
of conversion. In this mode the serial clock rate is determined by
the master clock rate of the part (at CLK IN input). The second
mode is an external clocking mode where the user provides the
frame sync and serial clock signals to obtain the serial data from the
part. In this second mode, the user has control of the serial clock
rate up to a maximum of 10 MHz. The two modes are discussed in
more detail in the Serial Interface section.
The part also provides hardware and software conversion start
features. The former provides a well-defined sampling instant
with the track/hold going into hold on the rising edge of the
CONVST
signal. For the software conversion start, a write to
the CONV bit to the Control Register initiates the conversion
sequence. However, for the software conversion start an internal
pulse has to time out before the input signal is sampled. This
pulse, plus the difficult in maintaining exactly equal delays
between each software conversion start command, means that
the dynamic performance of the AD7890 may have difficulty
meeting spec when used in software conversion start mode.
The AD7890 provides separate channel select and conversion start
control. This allows the user to optimize the throughput rate of the
system. Once the track/hold has gone into hold mode, the input
channel can be updated and the input voltage can settle to the new
value while the present conversion is in progress.
Assuming the internal pulse has timed out before the CONVST
pulse is exercised, the conversion will consist of 14.5 master
clock cycles. In the self-clocking mode, the conversion time is
defined as the time from the rising edge of CONVST to the fall-
ing edge of RFS (i.e., when the device starts to transmit its con-
version result). This time includes the 14.5 master clock cycles
plus the updating of the output register and delay time in out-
putting the RFS signal, resulting in a total conversion time of
5.9
µs maximum. Figure 4 shows the conversion timing for the
AD890 when used in the Self-Clocking (Master) Mode with
hardware CONVST. The timing diagram assumes that the
internal pulse is not active when the CONVST signal goes high.
To ensure this, the channel address to be converted should be
selected by writing to the Control Register prior to the
CONVST
pulse. Sufficient setup time should be allowed
between the Control Register write and the CONVST to ensure
that the internal pulse has timed out. The duration of the inter-
nal pulse (and hence the duration of setup time) depends on the
value of CEXT.
Track/Hold Section
The SHA IN input on the AD7890 connects directly to the
input stage of the track/hold amplifier. This is a high impedance
input with input leakage currents of less than 50 nA. Connect-
ing the MUX OUT pin directly to the SHA IN pin connects the
multiplexer output directly to the track/hold amplifier. The
input voltage range for this input is 0 V to +2.5 V. If external
circuitry is connected between MUX OUT and SHA IN, then
the user must ensure that the input voltage range to the SHA
IN input is 0 V to +2.5 V to ensure that the full dynamic range
of the converter is utilized.
The track/hold amplifier on the AD7890 allows the ADC to
accurately convert an input sine wave of full-scale amplitude to
12-bit accuracy. The input bandwidth of the track/hold is
greater than the Nyquist rate of the ADC even when the ADC is
operated at its maximum throughput rate of 117 kHz (i.e., the
track/hold can handle input frequencies in excess of 58 kHz).
The track/hold amplifier acquires an input signal to 12-bit accu-
racy in less than 2
µs. The operation of the track/hold is essen-
tially transparent to the user. The track/hold amplifier goes from
its tracking mode to its hold mode at the start of conversion.
The start of conversion is the rising edge of CONVST (assum-
ing the internal pulse has timed out) for hardware conversion
starts and for software conversion starts is the point where the
internal pulse is timed out. The aperture time for the track/hold
(i.e., the delay time between the external CONVST signal and
the track/hold actually going into hold) is typically 15 ns. For
software conversion starts, the time depends on the internal
pulse widths. Therefore, for software conversion starts, the sam-
pling instant is not very well defined. For sampling systems
which require well defined, equidistant sampling, it may not be
possible to achieve optimum performance from the part using
the software conversion start. At the end of conversion, the part
returns to its tracking mode. The acquisition time of the track/
hold amplifier begins at this point.
Reference Section
The AD7890 contains a single reference pin, labelled
REF OUT/REF IN, which either provides access to the part’s
own +2.5 V reference or to which an external +2.5 V reference
can be connected to provide the reference source for the part.
The part is specified with a +2.5 V reference voltage. Errors in
the reference source will result in gain errors in the AD7890’s
transfer function and will add to the specified full-scale errors
on the part. On the AD7893-10, it will also result in an offset
error injected in the attenuator stage.
The AD7890 contains an on-chip +2.5 V reference. To use this
reference as the reference source for the AD7890, simply con-
nect a 0.1
µF disc ceramic capacitor from the REF OUT/ REF
IN pin to AGND. The voltage which appears at this pin is inter-
nally buffered before being applied to the ADC. If this reference
is required for use external to the AD7890, it should be buffered
as the source impedance of this output is 2 k
Ω nominal. The
tolerance on the internal reference is
±10 mV at 25°C with a
typical temperature coefficient of 25 ppm/
°C and a maximum
error over temperature of
±25 mV.


유사한 부품 번호 - AD7890AN-4

제조업체부품명데이터시트상세설명
logo
Analog Devices
AD7890AN-4 AD-AD7890AN-4 Datasheet
392Kb / 29P
   8-Channel, 12-Bit Serial Data Acquisition System
More results

유사한 설명 - AD7890AN-4

제조업체부품명데이터시트상세설명
logo
Analog Devices
AD7890 AD-AD7890_17 Datasheet
392Kb / 29P
   8-Channel, 12-Bit Serial Data Acquisition System
AD7891 AD-AD7891 Datasheet
173Kb / 20P
   LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
REV. A
AD7891YSZ-2 AD-AD7891YSZ-2 Datasheet
1Mb / 20P
   LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
REV. D
AD7891AP AD-AD7891AP Datasheet
316Kb / 20P
   LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
REV. D
AD7891 AD-AD7891_04 Datasheet
1Mb / 20P
   LC2MOS 8-Channel, 12-Bit High Speed Data Acquisition System
REV. D
AD7890 AD-AD7890_15 Datasheet
480Kb / 28P
   LC MOS 8-Channel, 12-Bit Serial Data Acquisition System
REV. C
AD7874 AD-AD7874 Datasheet
414Kb / 16P
   LC2MOS 4-Channel, 12-Bit Simultaneous Sampling Data Acquisition System
REV. C
5962-9152101MXA AD-5962-9152101MXA Datasheet
326Kb / 16P
   LC2MOS 4-Channel, 12-Bit Simultaneous Sampling Data Acquisition System
REV. C
AD7874SQ AD-AD7874SQ Datasheet
326Kb / 16P
   LC2MOS 4-Channel, 12-Bit Simultaneous Sampling Data Acquisition System
REV. C
AD7874BNZ AD-AD7874BNZ Datasheet
326Kb / 16P
   LC2MOS 4-Channel, 12-Bit Simultaneous Sampling Data Acquisition System
REV. C
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20


데이터시트 다운로드

Go To PDF Page


링크 URL




개인정보취급방침
ALLDATASHEET.CO.KR
ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com