전자부품 데이터시트 검색엔진 |
|
AD7888ARUZ-REEL7 데이터시트(PDF) 7 Page - Analog Devices |
|
AD7888ARUZ-REEL7 데이터시트(HTML) 7 Page - Analog Devices |
7 / 17 page AD7888 –7– CONTROL REGISTER The Control Register on the AD7888 is an 8-bit, write-only register. Data is loaded from the DIN pin of the AD7888 on the rising edge of SCLK. The data is transferred on the DIN line at the same time as the conversion result is read from the part. This requires 16 serial clocks for every data transfer. Only the information provided on the first 8 rising clock edges (after CS falling edge) is loaded to the Control Register. MSB denotes the first bit in the data stream. The bit functions are outlined in Table I. The default contents of the Control Register on power-up is all zeros. Table I. Control Register Bit Function Description MSB C T N O DO R E Z2 D D A1 D D A0 D D AF E R1 M P0 M P Bit Mnemonic Comment 7 DONTC Don’t Care. The value written to this bit of the Control Register is a don’t care, i.e., it doesn’t matter if the bit is 0 or 1. 6 ZERO A zero must be written to this bit to ensure correct operation of the AD7888. 5 ADD2 These three address bits are loaded at the end of the present conversion sequence and select which analog input 4 ADD1 channel is converted for the next conversion. The selected input channel is decoded as shown in Table II. 3 ADD0 2 REF Reference Bit. With a 0 in this bit, the on-chip reference is enabled. With a 1 in this bit, the on-chip reference is disabled. To obtain best performance from the AD7888, the internal reference should be disabled when using an externally applied reference source. (See On-Chip Reference section.) 1, 0 PM1, PM0 Power Management Bits. These two bits decode the mode of operation of the AD7888 as shown in Table III. PERFORMANCE CURVES Figure 2 shows a typical FFT plot for the AD7888 at 100 kHz sample rate and 10 kHz input frequency. FREQUENCY – kHz –10 0 48.83 12.21 24.41 36.62 –30 –50 –70 –90 –110 4096 POINT FFT SAMPLING 100kSPS fIN = 10kHz SNR = 70dB Figure 2. Dynamic Performance Figure 3 shows a typical plot for the SNR vs. frequency for a 5 V supply and with a 5 V external reference. 71.0 0 42.14 73.0 72.5 72.0 71.5 10.89 31.59 VDD = 5V 5V EXT REFERENCE 21.14 INPUT FREQUENCY – kHz Figure 3. SNR vs. Input Frequency REV. C |
유사한 부품 번호 - AD7888ARUZ-REEL7 |
|
유사한 설명 - AD7888ARUZ-REEL7 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |