전자부품 데이터시트 검색엔진 |
|
TS30023 데이터시트(PDF) 4 Page - List of Unclassifed Manufacturers |
|
TS30023 데이터시트(HTML) 4 Page - List of Unclassifed Manufacturers |
4 / 19 page TRIUNE SYSTEMS PROPRIETARY & CONFIDENTIAL INFORMATION - 4 - TS30021/22/23 Version 1.5 Specifications subject to change WWW.TRIUNESYSTEMS.COM Copyright © 2013, Triune Systems, LLC ABSOLUTE MAXIMUM RATINGS Over operating free–air temperature range unless otherwise noted(1, 2) Parameter Value Unit VCC, VLDO -0.3 to 18 V BST -0.3 to (VCC+6) V VSW -1 to 18 V EN, PG,FB, FBLDO, VOLDO -0.3 to 6 V Electrostatic Discharge – Human Body Model +/-2k V Electrostatic Discharge – Charge Device Model +/-500 V Lead Temperature (soldering, 10 seconds) 260 C (1) Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability. (2) All voltage values are with respect to network ground terminal. THERMAL CHARACTERISTICS Symbol Parameter Value Unit JA Thermal Resistance Junction to Air (Note 1) 38 °C/W TSTG Storage Temperature Range -65 to 150 °C TJ MAX Maximum Junction Temperature 150 °C TJ Operating Junction Temperature Range -40 to 125 °C Note 1: Assumes 16LD 3x3 QFN with hi-K JEDEC board and 13.5 inch2 of 1 oz Cu RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Typ Max Unit VCC Input Operating Voltage 4.5 12 16 V VLDO LDO Input Operating Voltage 2.2 16 V CBST Bootstrap Capacitor 17.6 22 26.4 nF LOUT Output Filter Inductor Typical Value (Note 1) 1.2 1.5 1.8 uH COUT Output Filter Capacitor Typical Value (Note 2) 17.6 22 uF COUT_LDO LDO Output Filter Capacitor Typical Value (Note 2) 1 uF COUT-ESR Output Filter Capacitor ESR 2 100 mW CBYPASS Input Supply Bypass Capacitor Typical Value (Note 3) 8 10 uF CBYPASS-LDO LDO Input Supply Bypass Capacitor Typical Value (Note 3) 8 10 uF Note 1: For best performance, an inductor with a saturation current rating higher than the maximum VOUT load requirement plus the inductor current ripple. Note 2: For best performance, a low ESR ceramic capacitor should be used. Note 3: For best performance, a low ESR ceramic capacitor should be used. If CBYPASS is not a low ESR ceramic capacitor, a 0.1uF ceramic capacitor should be added in parallel to CBYPASS. |
유사한 부품 번호 - TS30023 |
|
유사한 설명 - TS30023 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |