전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

AM79C32A 데이터시트(PDF) 6 Page - Advanced Micro Devices

부품명 AM79C32A
상세설명  Digital Subscriber Controller??(DSC?? Circuit
Download  101 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  AMD [Advanced Micro Devices]
홈페이지  http://www.amd.com
Logo AMD - Advanced Micro Devices

AM79C32A 데이터시트(HTML) 6 Page - Advanced Micro Devices

Back Button AM79C32A Datasheet HTML 2Page - Advanced Micro Devices AM79C32A Datasheet HTML 3Page - Advanced Micro Devices AM79C32A Datasheet HTML 4Page - Advanced Micro Devices AM79C32A Datasheet HTML 5Page - Advanced Micro Devices AM79C32A Datasheet HTML 6Page - Advanced Micro Devices AM79C32A Datasheet HTML 7Page - Advanced Micro Devices AM79C32A Datasheet HTML 8Page - Advanced Micro Devices AM79C32A Datasheet HTML 9Page - Advanced Micro Devices AM79C32A Datasheet HTML 10Page - Advanced Micro Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 6 / 101 page
background image
6
Am79C30A/32A Data Sheet
PIN DESCRIPTION*
Line Interface Unit (LIU)
HSW
Hook-Switch (Input)
The HSW signal indicates if the hook-switch is on or off
hook. This signal may be generated with a mechanical
switch wired to ground with a pull-up resistor to VCC.
Any change in the HSW state causes an interrupt.
LIN1, LIN2
Subscriber Line Input (Differential Inputs)
The LIN1 and LIN2 inputs interface to the subscriber (S
reference point) via an isolation transformer. LIN2 is the
positive input; LIN1 is the negative input. These pins
are not TTL compatible.
LOUT1, LOUT2
Subscriber Line Output (Differential Outputs)
The LOUT1 and LOUT2 line driver output signals inter-
face to the subscriber line at the S reference point via
an isolation transformer and resistors. LOUT2 is the
positive S-interface driver (sources current during a
High mark), and LOUT1 is the negative S-interface
dr i ver ( sou rce s cur ren t d ur i ng Low m a r k). Fo r
multi-point applications, all TEs must maintain the
same polarity on the S Interface. These pins are not
TTL compatible.
Main Audio Processor (MAP)
All MAP pins are analog, and therefore are not TTL
compatible.
AINA, AINB
Analog (Inputs)
These analog inputs allow for two separate analog (au-
dio) inputs to the transmit path of the codec/filter.Input
signals on either of these pins must be referenced to
AREF.
AREF
Analog Reference (Output)
This is a nominal 2.25-V reference voltage output for bi-
asing the analog inputs. When the MAP is disabled,
this pin is high impedance.
CAP1, CAP2
Capacitor/Resistor (CAP1, Input; CAP2, Output)
An external resistor and capacitor are connected in se-
ries between these pins. These components are
needed for the integrator in the Analog-to-Digital Con-
verter (ADC).
EAR1, EAR2
Earpiece Interface (Differential Outputs)
EAR1 and EAR2 are the outputs from the receive path
of the codec/filter. These differential outputs can di-
rectly drive a minimum load of 130 ohms.
LS1, LS2
Loudspeaker Interface (Differential Outputs)
LS1 and LS2 are push-pull outputs which can directly
drive a minimum load of 40 ohms.
Microprocessor Interface (MPI)
A2–A0
Address Line (Inputs)
A2, A1, and A0 signals select source and destination
registers for read and write operations on the data bus.
CS
Chip Select (Input)
CS must be Low to read or write to the Am79C30A/
32A. Data transfer occurs over the bidirectional data
lines (D7–D0).
D7–D0
Data Bus (Bidirectional with High-Impedance State)
The eight bidirectional data bus lines are used to ex-
change information with the microprocessor. D0 is the
least significant bit (LSB) and D7 is the most significant
bit (MSB). A High on the data bus line corresponds to
a logic 1, and Low corresponds to a logic 0. These lines
act as inputs when both WR and CS are active and as
outputs when both RD and CS are active. When CS is
inactive or both RD and WR are inactive, the D7–D0
pins are in a high-impedance state.
INT
Interrupt (Output)
An active Low output on the INT pin informs the exter-
nal microprocessor that the Am79C30A/32A needs in-
terrupt service. INT is updated once every 125 µs. The
INT pin remains active until the Interrupt Register (IR)
is read or the Am79C30A/32A is reset.
RESET
Reset (Input)
Reset is an active High signal which causes the
Am79C30A/32A to immediately terminate its present
activity and initialize to the reset condition. When reset
returns Low, the Am79C30A/32A enters the Idle mode.
The MCLK output remains active while RESET is held
High.
Note:
* All signal levels are TTL compatible unless otherwise stated.


유사한 부품 번호 - AM79C32A

제조업체부품명데이터시트상세설명
logo
Advanced Micro Devices
AM79C02 AMD-AM79C02 Datasheet
723Kb / 48P
   Dual Subscriber Line Audio Processing Circuit (DSLAC) Devices
AM79C02AJC AMD-AM79C02AJC Datasheet
723Kb / 48P
   Dual Subscriber Line Audio Processing Circuit (DSLAC) Devices
AM79C02JC AMD-AM79C02JC Datasheet
723Kb / 48P
   Dual Subscriber Line Audio Processing Circuit (DSLAC) Devices
AM79C03 AMD-AM79C03 Datasheet
723Kb / 48P
   Dual Subscriber Line Audio Processing Circuit (DSLAC) Devices
logo
List of Unclassifed Man...
AM79C031 ETC1-AM79C031 Datasheet
501Kb / 48P
   Advanced Subscriber Line Interface Circuit (ASLIC) Device
More results

유사한 설명 - AM79C32A

제조업체부품명데이터시트상세설명
logo
Texas Instruments
SM320F28335-HT TI-SM320F28335-HT Datasheet
1Mb / 158P
[Old version datasheet]   Digital Signal Controller (DSC)
SM320F28335PTPMEP TI-SM320F28335PTPMEP Datasheet
1Mb / 167P
[Old version datasheet]   Digital Signal Controller (DSC)
SM320F28335-EP TI1-SM320F28335-EP_16 Datasheet
1Mb / 167P
[Old version datasheet]   Digital Signal Controller (DSC)
SM320F28335-HT TI1-SM320F28335-HT_14 Datasheet
1Mb / 182P
[Old version datasheet]   Digital Signal Controller (DSC)
SM320F28335-EP TI1-SM320F28335-EP_12 Datasheet
1Mb / 167P
[Old version datasheet]   Digital Signal Controller (DSC)
SM320F28335-EP TI-SM320F28335-EP Datasheet
1Mb / 169P
[Old version datasheet]   Digital Signal Controller (DSC)
SM320F28335GJZMEP TI1-SM320F28335GJZMEP Datasheet
1Mb / 167P
[Old version datasheet]   Digital Signal Controller (DSC)
logo
Zarlink Semiconductor I...
MT9171 ZARLINK-MT9171_06 Datasheet
553Kb / 28P
   Digital Subscriber Interface Circuit Digital Network Interface Circuit
logo
Mitel Networks Corporat...
MT9173 MITEL-MT9173 Datasheet
411Kb / 22P
   Digital Subscriber Interface Circuit with RxSB
logo
Zarlink Semiconductor I...
MT9173 ZARLINK-MT9173 Datasheet
613Kb / 28P
   Digital Subscriber Interface Circuit with RxSB Digital Network Interface Circuit with RxSB
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


데이터시트 다운로드

Go To PDF Page


링크 URL




개인정보취급방침
ALLDATASHEET.CO.KR
ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com