Specification

50 150 Watts

•

AC Input LED Driver

•

Constant Voltage & Current Operation

•

High Power Factor

•

High Efficiency

•

Water Proof to IP67

•

90 305 VAC Input Voltage Range

•

3 Year Warranty

DLG Series

Input

Input Voltage

• 90-305 VAC, see derating curve

Input Frequency

• 47-63 Hz

Input Current

• 50 W: 1.0 A at 115 VAC, 0.5 A at 230 VAC,

75 W: 1.2 A at 115 VAC, 0.6 A at 230 VAC,

100 W: 1.4 A at 115 VAC, 0.7 A at 230 VAC,

150 W: 2.0 A at 115 VAC, 1.0 A at 230 VAC

Inrush Current

• 65 A at 230 VAC, cold start +25 °C

Power Factor

• >0.94 at 230 VAC, full load

Earth Leakage Current

• DLG50/75: 500 µA max at 230 VAC

DLG100/150: 750 µA max at 230 VAC

No Load Input Power

• 0.6 W max at 230 VAC

Input Protection

• DLG50/75 T2.5A/300V fuse fitted in line,

DLG100 T3.15A/300V fuse fitted in line,

DLG150 T4A/300V fuse fitted in line

Output

Output Voltage

• See table

Minimum Load

• No minimum load required

Start Up Delay

• 1.5 s max at 115 VAC

Hold Up Time

• DLG50/75: No hold up

DLG100/150: 16 ms minimum

Line Regulation

• ±0.5%

Load Regulation

• ±1.0% in constant voltage mode,

±5.0% in constant current mode

Turn On Overshoot

• 5% max

Transient Response

• 5% maximum deviation, recovery to within

1% in 10 ms for a 50% load change

Ripple & Noise

DLG100/150: 150 mV pk-pk up to 36 V

output, 200 mV for 48 V output, 240 mV

for ≥54 V output (see note 2)

Overvoltage Protection

• 110-142%, recycle mains to reset, only on

DLG100 & DLG150 versions

Overtemperature

• Unit shuts down, recycle mains to reset

Protection

Overload Protection

• 105% maximum, auto recovery

Short Circuit Protection

• Trip and restart (hiccup mode)

Temperature

• 0.04%/°C

Coefficient

xppower.com

General

Efficiency

• See table

Isolation

• 3750 VAC Input to Output

1880 VAC Input to Ground

500 VAC Output to Ground

Switching Frequency

• DLG50/75: 40-80 kHz

DLG100/150: PWM 60-80 kHz,

PFC 55-133 kHz

MTBF

• >200 kHrs to MIL-HDBK-217F at 25 °C, GB

Environmental

Operating Temperature

• DLG50/75: -40 °C to +60 °C

(see derating curve),

DLG100/150: -30 °C to +70 °C

(see derating curve)

Operating Humidity

• 5-100% RH, non-condensing

Storage Temperature

• -40 °C to +80 °C

Operating Altitude

• 3000 m

Vibration

• 10-500 Hz, 2 g, 10 mins/cycle, 6 cycles in

each of 3 axes

EMC & Safety

Emissions

• EN55015, class B conducted and radiated

Harmonic Currents

• EN61000-3-2, class A

EN61000-3-2, class C for loads >80%

Voltage Flicker

• EN61000-3-3

ESD Immunity

• EN61000-4-2, 8 kV air and 4 kV contact,

Perf Criteria A

Radiated Immunity

• EN61000-4-3, level 2 Perf Criteria A

EFT/Burst

• EN61000-4-4, level 2 Perf Criteria A

Surge

• EN61000-4-5, installation class 3,

Perf Criteria A

Conducted Immunity

• EN61000-4-6, level 2 Perf Criteria A

Dips & Interruptions

• EN61000-4-11, 30% 10 ms,

60% 100 ms, 100% 5000 ms,

Perf Criteria A, B, B

Safety Approvals

• EN61347, UL8750, CE Mark

DLG100/150: IEC60950-1, EN60950-1,

UL60950-1

Notes

1. DLG50/75 use a topology which results in increased levels of mains frequency

related ripple. Contact technical sales for details.