전자부품 데이터시트 검색엔진 |
|
SLA2601M 데이터시트(PDF) 2 Page - Sanken electric |
|
SLA2601M 데이터시트(HTML) 2 Page - Sanken electric |
2 / 2 page 133 ICs ■Typical Connection Diagram (Unit : mm) ■External Dimensions (ZIP24 with Fin [SLA24Pin]) φ3.2±0.15 31±0.2 24.4±0.2 16.4±0.2 31.3±0.2 Gate burr JAPAN A B 23 X P1.27±0.7=29.21±1 (Including the resin burr) (Measured at the tip) 13 57 9 11 13 15 17 19 21 23 24 68 10 12 14 16 18 20 22 24 0.6 +0.15 -0.05 φ3.2±0.15 X 3.8 2.45±0.2 4.8±0.2 1.7±0.1 4.5±0.7 R-end (Measured at the root) (Measured at the tip) Pins 4, 5, 8, 9, 16, 17, 20, and 21 are cut pins. 0.5 +0.15 -0.05 4-(R1) φ3.2±0.15 31±0.2 24.4±0.2 16.4±0.2 31.3±0.2 Gate burr JAPAN A B 23 X P1.27±0.7=29.21±1 (Including the resin burr) (Measured at the tip) 13 57 9 11 13 15 17 19 21 23 24 68 10 12 14 16 18 20 22 24 0.6 +0.15 -0.05 φ3.2±0.15 X 3.8 2.45±0.2 4.8±0.2 1.7±0.1 2.5±0.6 R-end (Measured at the root) (Measured at the tip) Pins 4, 5, 8, 9, 16, 17, 20, and 21 are cut pins. 0.5 +0.15 -0.05 2-(R1) SLA2601M/SLA2602M The input pull-down resistor is built in IC (about 22 kΩ). However, if the input is expected to be unstable or to fluctuate greatly, it needs to be reinforced using an external resistor. Attach capacitors near the IC. Attach a ceramic capacitor in parallel with the electrolytic capacitor if too much noise is generated. When inserting a current sense resistor between LS1/LS2 and COM, make sure to specify the resistance so that the voltage between LS1/LS2 and COM is 1 V or less. Forming No. 2176 Forming No. 2179 ■Pin Assignment Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Symbol LSI VM1 VM1 (LG1) (LG1) VBB1 VB1 (LG1) (LG1) EN IN COM COM VCC FO (LG2) (LG2) VB2 VBB2 (LG2) (LG2) VM2 VM2 LS2 Function MOSFET L1 source pin/MOSFET L2 source pin MOSFET H1 source pin/MOSFET L1 drain pin Same as above Cut pin (MOSFET L1 gate pin) Same as above MOSFET H1 drain pin/MOSFET H2 drain pin High side floating power supply pin 1 Cut pin (MOSFET L1 gate pin) Same as above Input pin for enabling output Input pin for switching output Pre-drive IC ground pin Same as above Pre-drive IC power supply pin Fo signal output pin Cut pin (MOSFET L2 gate drive pin) Same as above High side floating power supply pin 2 MOSFET H1 drain pin/MOSFET H2 drain pin Cut pin (L2 gate drive pin) Same as above MOSFET H2 source pin/MOSFET L2 drain pin Same as above MOSFET L1 source pin/MOSFET L2 source pin ■Truth Table EN IN FO H1 H2 L1 L2 LX X OFF OFF OFF OFF XX H OFF OFF OFF OFF HH L ON OFF OFF ON HL L OFF ON ON OFF Product Mass: Approx. 6.2 g |
유사한 부품 번호 - SLA2601M |
|
유사한 설명 - SLA2601M |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |