전자부품 데이터시트 검색엔진 |
|
HCPL-5400 데이터시트(PDF) 8 Page - Agilent(Hewlett-Packard) |
|
HCPL-5400 데이터시트(HTML) 8 Page - Agilent(Hewlett-Packard) |
8 / 12 page 1-531 Notes: 1. Not to exceed 5% duty factor, not to exceed 50 µsec pulse width. 2. All devices are considered two-terminal devices: measured between all input leads or terminals shorted together and all output leads or terminals shorted together. 3. This is a momentary withstand test, not an operating condition. 4. t PHL propagation delay is measured from the 50% point on the rising edge of the input current pulse to the 1.5 V point on the falling edge of the output pulse. The t PLH propagation delay is measured from the 50% point on the falling edge of the input current pulse to the 1.5 V point on the rising edge of the output pulse. Pulse Width Distortion, PWD = |t PHL - tPLH|. 5. CM L is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state (V O(MAX) < 0.8 V). CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state (V O(MIN) > 2.0 V). 6. Duration of output short circuit time not to exceed 10 ms. 7. Power Supply Noise Immunity is the peak to peak amplitude of the ac ripple voltage on the V CC line that the device will withstand and still remain in the desired logic state. For desired logic high state, V OH(MIN) > 2.0 V, and for desired logic low state, VOL(MAX) < 0.8 V. 8. Measured between adjacent input pairs shorted together for each multichannel device. 9. Each channel. 10. Standard parts receive 100% testing at 25 °C (Subgroups 1 and 9). SMD and hi-rel parts receive 100% testing at 25, 125, and –55°C (Subgroups 1 and 9, 2 and 10, 3 and 11, respectively). 11. Parameters are tested as part of device initial characterization and after design and process changes. Parameters are guaranteed to limits specified for all lots not specifically tested. 12. Propagation delay skew is defined as the difference between the minimum and maximum propagation delays for any given group of optocouplers with the same part number that are all switching at the same time under the same operating conditions. 13. The HCPL-6430 and HCPL-6431 dual channel parts function as two independent single channel units. Use the single channel parameter limits. Figure 1. Typical Logic Low Output Voltage vs. Logic Low Output Current. Figure 2. Typical Logic High Output Voltage vs. Logic High Output Current. Figure 3. Typical Output Voltage vs. Input Forward Current. Figure 4. Typical Diode Input Forward Current Characteristic. |
유사한 부품 번호 - HCPL-5400 |
|
유사한 설명 - HCPL-5400 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |