전자부품 데이터시트 검색엔진 |
|
TDA2030L-TA5-T 데이터시트(PDF) 8 Page - Unisonic Technologies |
|
TDA2030L-TA5-T 데이터시트(HTML) 8 Page - Unisonic Technologies |
8 / 13 page TDA2030 LINEAR INTEGRATED CIRCUIT UNISONICTECHNOLOGIESCO.,LTD 8 of 13 www.unisonic.com.tw QW-R107-004,D MULTIWAY SPEAKER SYSTEMS AND ACTIVE BOXES Multiway loudspeaker systems provide the best possible acoustic performance since each loudspeaker is specially designed and optimized to handle a limited range of frequencies. Commonly, these loudspeaker systems divide the audio spectrum two or three bands. To maintain a flat frequency response over the Hi-Fi audio range the bands cobered by each loudspeaker must overlap slightly. Imbalance between the loudspeakers produces unacceptable results therefore it is important to ensure that each unit generates the correct amount of acoustic energy for its segments of the audio spectrum. In this respect it is also important to know the energy distribution of the music spectrum to determine the cutoff frequencies of the crossover filters(see Fig. 2).As an example, a 100W three-way system with crossover frequencies of 400Hz and 3KHz would require 50W for the woofer,35W for the midrange unit and 15W for the tweeter. Both active and passive filters can be used for crossovers but active filters cost significantly less than a good passive filter using aircored inductors and non-electrolytic capacitors. In addition active filters do not suffer from the typical defects of passive filters: --Power less; --Increased impedance seen by the loudspeaker(lower damping) --Difficulty of precise design due to variable loudspeaker impedance. Obviously, active crossovers can only be used if a power amplifier is provide for each drive unit. This makes it particularly interesting and economically sound to use monolithic power amplifiers. In some applications complex filters are not relay necessary and simple RC low-pass and high-pass networks(6dB/octave) can be recommended. The result obtained are excellent because this is the best type of audio filter and the only one free from phase and transient distortion. The rather poor out of band attenuation of single RC filters means that the loudspeaker must operate linearly well beyond the crossover frequency to avoid distortion. A more effective solution is shown in Fig. 3. The proposed circuit can realize combined power amplifiers and 12dB/octave or high-pass or low-pass filters. In proactive, at the input pins amplifier two equal and in-phase voltages are available, as required for the active filter operations. The impedance at the Pin(-) is of the order of 100 Ω,while that of the Pin (+) is very high, which is also what was wanted. The components values calculated for fc=900Hz using a Bessel 3rd Sallen and Key structure are: C1=C2=C3=22nF,R1=8.2K Ω,R2=5.6KΩ,R3=33KΩ. Using this type of crossover filter, a complete 3-way 60W active loudspeaker system is shown in Fig. 20. It employs 2nd order Buttherworth filter with the crossover frequencies equal to 300Hz and 3kHz. The midrange section consistors of two filters a high pass circuit followed by a low pass network. With Vs=36V the output power delivered to the woofer is 25W at d=0.06%( 30W at d=0.5%).The power delivered to the midrange and the tweeter can be optimized in the design phase taking in account the loudspeaker efficiency and impedance (RL=4 Ω to 8Ω). |
유사한 부품 번호 - TDA2030L-TA5-T |
|
유사한 설명 - TDA2030L-TA5-T |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |