 |
전자부품 데이터시트 검색엔진 |
|
|
전자부품 데이터시트 검색엔진 |
|
TC642CUA 데이터시트(PDF) 7 Page - Microchip Technology |
|
||||||||||||||||||||||||||||||
TC642CUA 데이터시트(HTML) 7 Page - Microchip Technology |
|
|
7 / 28 page  2002 Microchip Technology Inc. DS21444C-page 7 TC642 4.0 SYSTEM BEHAVIOR The flowcharts describing the TC642’s behavioral algorithm are shown in Figure 4-1. They can be summarized as follows: 4.1 Power-Up (1) Assuming the device is not being held in shutdown mode (VMIN > VREL)… (2) Turn VOUT output on for 32 cycles of the PWM clock. This ensures that the fan will start from a dead stop. (3) During this Start-up Timer, if a fan pulse is detected, branch to Normal Operation; if none are received… (4) Activate the 32-cycle Start-up Timer one more time and look for a fan pulse; if a fan pulse is detected, proceed to Normal Operation; if none are received… (5) Proceed to Fan Fault. (6) End. 4.2 Normal Operation Normal Operation is an endless loop which may only be exited by entering shutdown mode or Fan Fault. The loop can be thought of as executing at the frequency of the oscillator and PWM. (1) Reset the missing pulse detector. (2) Is TC642 in shutdown? If so… a. VOUT duty cycle goes to zero. b. FAULT is disabled. c. Exit the loop and wait for VMIN > VREL to resume operation (indistinguishable from power-up). (3) If an over-temperature fault occurs (VIN > VOTF), activate FAULT; release FAULT when VIN < VOTF. (4) Drive VOUT to a duty cycle proportional to the greater of VIN and VMIN on a cycle by cycle basis. (5) If a fan pulse is detected, branch back to the start of the loop (1). (6) If the missing pulse detector times out … (7) Activate the 3-cycle Diagnostic Timer and look for pulses; if a fan pulse is detected, branch back to the start of the loop (1); if none are received… (8) Activate the 32-cycle Start-up Timer and look for pulses; if a fan pulse is detected, branch back to the start of the loop (1); if none are received… (9) Quit Normal Operation and go to Fan Fault. (10) End. 4.3 Fan Fault Fan fault is an infinite loop wherein the TC642 is latched in shutdown mode. This mode can only be released by a reset (i.e., VMIN being brought below VSHDN, then above VREL, or by power-cycling). (1) While in this state, FAULT is latched on (low) and the VOUT output is disabled. (2) A reset sequence applied to the VMIN pin will exit the loop to Power-Up. (3) End. |
유사한 부품 번호 - TC642CUA |
|
유사한 설명 - TC642CUA |
|
|
|
링크 URL |
| 개인정보취급방침 |
| ALLDATASHEET.CO.KR |
| ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Korean ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
