전자부품 데이터시트 검색엔진 |
|
543502-1 데이터시트(PDF) 1 Page - TE Connectivity Ltd |
|
543502-1 데이터시트(HTML) 1 Page - TE Connectivity Ltd |
1 / 4 page ©2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company All Rights Reserved *Trademark TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. 1 of 4 Instruction Sheet TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com LOC B Cover Lacing Fixture 91293-1 for AMPLIMITE* .050 Series Connectors and AMPMODU* 50/50 Grid Connectors 408-9750 08 APR 11 Rev D Figure 1 1. INTRODUCTION Cover Lacing Fixture 91293-1 is used with Manual Arbor Frame Assembly 58024-1 to apply discrete wires to AMPLIMITE .050 Series connectors and wire lacing termination covers for AMPMODU 50/50 grid connectors. Refer to Instruction Sheet 408-6923 for the operating procedure for the arbor frame. Dimensions in this instruction sheet are in metric units [with U.S. customary units in brackets]. Figures are not drawn to scale. Reasons for reissue of this instruction sheet are provided in Section 6, REVISION SUMMARY. 2. DESCRIPTION (Figure 1) The fixture consists of a slide assembly, a lacing fixture subassembly, and an upper tooling assembly containing two 50-position and two 100-position seating bars. Additional seating bars, purchased separately, are available for applying 26- and 68- position connectors. The slide assembly consists of a slide body and a slide stop. The slide body mounts to the base of the manual arbor frame assembly and allows the lacing fixture subassembly to slide back into position under the upper tooling assembly. The slide stop, which is used to position the lacing fixture subassembly under the upper tooling assembly, is a thin bar of steel that is fastened to the back of the slide at one of two positions. The lacing fixture subassembly consists of a U-shaped base with slots to hold the termination covers. Each slot has a stationary locator and an adjustable locator that permit proper positioning of the termination covers. Mounted onto the base are four combs (two inner combs and two outer combs), which are used to guide and hold the wires as they are pressed into the termination covers during the termination procedure. On the underside of the base is a cable clamp which holds the jacketed cable while the wires from the cable are being laced into the combs. The upper tooling assembly features a tool mount, a top plate, four seating bars, and two cutting blades. The inner seating bars push the wires at the inside edge of the termination cover. The center seating bars, which push the wires down inside the termination cover, must be installed to match the termination cover size being applied. The cutting blades help push the wires downward at the outside edge of the connector, and then cut the wires nearly flush with the connector edge. Combs Adjustable Locator Lacing Fixture Subassembly Upper Tooling Assembly Slots for Termination Covers Slide Stop Slide Body Stationary Locator NOTE i |
유사한 부품 번호 - 543502-1 |
|
유사한 설명 - 543502-1 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |