전자부품 데이터시트 검색엔진 |
|
ADV7184 데이터시트(PDF) 7 Page - Analog Devices |
|
ADV7184 데이터시트(HTML) 7 Page - Analog Devices |
7 / 108 page ADV7184 Rev. 0 | Page 7 of 108 TIMING SPECIFICATIONS At AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V. Operating temperature range, unless otherwise noted. Table 3. Parameter1,2 Symbol Test Conditions Min Typ Max Unit SYSTEM CLOCK AND CRYSTAL Nominal Frequency 28.63636 MHz Frequency Stability ±50 ppm I2C PORT3 SCLK Frequency 400 kHz SCLK Min Pulse Width High t1 0.6 μs SCLK Min Pulse Width Low t2 1.3 μs Hold Time (Start Condition) t3 0.6 μs Setup Time (Start Condition) t4 0.6 μs SDA Setup Time t5 100 ns SCLK and SDA Rise Time t6 300 ns SCLK and SDA Fall Time t7 300 ns Setup Time for Stop Condition t8 0.6 μs RESET FEATURE Reset Pulse Width 5 ms CLOCK OUTPUTS LLC1 Mark Space Ratio t9:t10 45:55 55:45 % duty cycle LLC1 Rising to LLC2 Rising t11 1 ns LLC1 Rising to LLC2 Falling t12 1 ns DATA AND CONTROL OUTPUTS Data Output Transitional Time4 t13 Negative clock edge to start of valid data; (tACCESS = t10 – t13) 3.6 ns Data Output Transitional Time4 t14 End of valid data to negative clock edge; (tHOLD = t9 + t14) 2.4 ns Propagation Delay to Hi-Z t15 6 ns Max Output Enable Access Time t16 7 ns Min Output Enable Access Time t17 4 ns 1 Temperature range TMIN to TMAX, –40°C to +85°C. The min/max specifications are guaranteed over this range. 2 Guaranteed by characterization. 3 TTL input values are 0 V to 3 V, with rise/fall times ≤3 ns, measured between the 10% and 90% points. 4 Timing figures obtained using default drive strength value (0xD5) in register subaddress 0xF4. ANALOG SPECIFICATIONS At AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V. Operating temperature range, unless otherwise noted. Recommended analog input video signal range: 0.5 V to 1.6 V, typically 1 V p-p. Table 4. Parameter1,2 Symbol Test Conditions Min Typ Max Unit CLAMP CIRCUITRY External Clamp Capacitor 0.1 μF Input Impedance3 Clamps switched off 10 MΩ Input impedance of Pin 40 (FB) 20 kΩ Large Clamp Source Current 0.75 mA Large Clamp Sink Current 0.75 mA Fine Clamp Source Current 17 μA Fine Clamp Sink Current 17 μA 1 Temperature range TMIN to TMAX, –40°C to +85°C. The min/max specifications are guaranteed over this range. 2 Guaranteed by characterization. 3 Except Pin 40 (FB). |
유사한 부품 번호 - ADV7184 |
|
유사한 설명 - ADV7184 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |