전자부품 데이터시트 검색엔진
  Korean  ▼

Delete All
ON OFF
ALLDATASHEET.CO.KR

X  

Preview PDF Download HTML

LT1762 데이터시트(HTML) 10 Page - Linear Technology

부품명 LT1762
상세내용  150mA, Low Noise, LDO Micropower Regulators
Download  16 Pages
Scroll/Zoom Zoom In 100% Zoom Out
제조사  LINER [Linear Technology]
홈페이지  http://www.linear.com
Logo 

LT1762 데이터시트(HTML) 10 Page - Linear Technology

Zoom Inzoom in Zoom Outzoom out
/ 16 page
 10 / 16 page
background image
10
LT1762 Series
GND (Pin 4): Ground.
SHDN (Pin5): Shutdown. The SHDN pin is used to put the
LT1762 regulators into a low power shutdown state. The
output will be off when the SHDN pin is pulled low. The
SHDN pin can be driven either by 5V logic or open-
collector logic with a pull-up resistor. The pull-up resistor
is required to supply the pull-up current of the open-
collector gate, normally several microamperes, and the
SHDN pin current, typically 1
µA. If unused, the SHDN pin
must be connected to VIN. The device will be in low power
shutdown state if the SHDN pin is not connected.
IN (Pin 8): Input. Power is supplied to the device through
the IN pin. A bypass capacitor is required on this pin if the
device is more than six inches away from the main input
filter capacitor. In general, the output impedance of a
battery rises with frequency, so it is advisable to include a
bypass capacitor in battery-powered circuits. A bypass
capacitor in the range of 1
µF to 10µF is sufficient. The
LT1762 regulators are designed to withstand reverse
voltages on the IN pin with respect to ground and the OUT
pin. In the case of a reverse input, which can happen if a
battery is plugged in backwards, the device will act as if
there is a diode in series with its input. There will be no
reverse current flow into the regulator and no reverse
voltage will appear at the load. The device will protect both
itself and the load.
OUT (Pin 1): Output. The output supplies power to the
load. A minimum output capacitor of 2.2
µF is required to
prevent oscillations. Larger output capacitors will be
required for applications with large transient loads to limit
peak voltage transients. See the Applications Information
section for more information on output capacitance and
reverse output characteristics.
SENSE (Pin 2): Output Sense. For fixed voltage versions
of the LT1762 (LT1762-2.5/LT1762-3/LT1762-3.3/
LT1762-5), the SENSE pin is the input to the error ampli-
fier. Optimum regulation will be obtained at the point
where the SENSE pin is connected to the OUT pin of the
regulator. In critical applications, small voltage drops are
caused by the resistance (RP) of PC traces between the
regulator and the load. These may be eliminated by con-
necting the SENSE pin to the output at the load as shown
in Figure 1 (Kelvin Sense Connection). Note that the
voltage drop across the external PC traces will add to the
dropout voltage of the regulator. The SENSE pin bias
current is 10
µA at the nominal rated output voltage. The
SENSE pin can be pulled below ground (as in a dual supply
system where the regulator load is returned to a negative
supply) and still allow the device to start and operate.
ADJ (Pin 2): Adjust. For the adjustable LT1762, this is the
input to the error amplifier. This pin is internally clamped
to
±7V. It has a bias current of 30nA which flows into the
pin (see curve of ADJ Pin Bias Current vs Temperature in
the Typical Performance Characteristics). The ADJ pin
voltage is 1.22V referenced to ground and the output
voltage range is 1.22V to 20V.
BYP (Pins 3): Bypass. The BYP pin is used to bypass the
reference of the LT1762 regulators to achieve low noise
performance from the regulator. The BYP pin is clamped
internally to
±0.6V (one VBE). A small capacitor from the
output to this pin will bypass the reference to lower the
output voltage noise. A maximum value of 0.01
µF can be
used for reducing output voltage noise to a typical 20
µVRMS
over a 10Hz to 100kHz bandwidth. If not used, this pin
must be left unconnected.
PIN FUNCTIONS
IN
SHDN
1762 F01
RP
OUT
VIN
SENSE
GND
LT1762
RP
4
2
1
5
8
+
+
LOAD
Figure 1. Kelvin Sense Connection


Html Pages

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16 


데이터시트 Download




링크 URL



Privacy Policy
ALLDATASHEET.CO.KR
ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ]  

Alldatasheet는?   |   광고문의    |   운영자에게 연락하기   |   개인정보취급방침   |   즐겨찾기   |   링크교환   |   제조사별 검색
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn