전자부품 데이터시트 검색엔진 |
|
AM29BDS320G 데이터시트(PDF) 32 Page - SPANSION |
|
AM29BDS320G 데이터시트(HTML) 32 Page - SPANSION |
32 / 74 page 30 Am29BDS320G 27243B1 October 1, 2003 Prelimin ary Reset Command Writing the reset command resets the banks to the read or erase-suspend-read mode. Address bits are don’t cares for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the bank to which the sys- tem was writing to the read mode. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence before programming begins (prior to the third cycle). This re- sets the bank to which the system was writing to the read mode. If the program command sequence is written to a bank that is in the Erase Suspend mode, writ- ing the reset command returns that bank to the erase-suspend-read mode. Once programming begins, however, the device ignores reset commands until the op- eration is complete. The reset command may be written between the sequence cycles in an autoselect command sequence. Once in the autoselect mode, the reset command must be written to return to the read mode. If a bank entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns that bank to the erase-suspend-read mode. If DQ5 goes high during a program or erase operation, writing the reset command returns the banks to the read mode (or erase-suspend-read mode if that bank was in Erase Suspend). The reset command is used to exit the sector lock/unlock sequence. This com- mand is required before reading from the bank selected for sector lock/unlock operations. Autoselect Command Sequence The autoselect command sequence allows the host system to access the manu- facturer and device codes, and determine whether or not a sector is protected. Table 14, “Command Definitions,” on page 36 shows the address and data re- quirements. The autoselect command sequence may be written to an address within a bank that is either in the read or erase-suspend-read mode. The autose- lect command may not be written while the device is actively programming or erasing in the other bank. The autoselect command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle that contains the bank address and the au- toselect command. The bank then enters the autoselect mode. No subsequent data will be made available if the autoselect data is read in synchronous mode. The system may read at any address within the same bank any number of times without initiating another autoselect command sequence. The following table de- scribes the address requirements for the various autoselect functions, and the resulting data. BA represents the bank address, and SA represents the sector ad- dress. The device ID is read in three cycles. |
유사한 부품 번호 - AM29BDS320G |
|
유사한 설명 - AM29BDS320G |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |