11

FN6334.1

March 5, 2007

Demo Board Schematic

Description of Operation and Application

Information

Theory Of Operation

The ISL59833 is a highly practical and robust marriage of

three high bandwidth, high speed, low power, rail-to-rail

voltage feedback amplifiers with a charge pump to provide a

negative rail without an additional power supply. Designed to

operate with a single supply voltage range from 0V to 3.3V,

the ISL59833 eliminates the need for a split supply with the

incorporation of a charge pump capable of generating a

bottom rail as much as 1.6V below ground for a 4.9V range

on a single 3.3V supply. This performance is ideal for NTSC

video with its negative-going sync pulses.

THE AMPLIFIER

The ISL59833 fabricated on a di-electrically isolated high

speed 5V Bi-CMOS process with 4GHz PNPs and NPN

transistor exceeding 20GHz - perfect for low distortion, low

power demand and high frequency circuits. While the

ISL59833 utilizes somewhat standard voltage mode

feedback topologies, there are many non-standard analog

features providing its outstanding bandwidth, rail-to-rail

operation, and output drive capabilities. The input signal

initially passes through a folded cascode, a topology

providing enhanced frequency response by essentially fixing

the base collector voltage at the junction of the input and

gain stage. The collector of each input device looks directly

into an emitter that is tied closely to ground through a

resistor and biased with a very stable DC source. Since the

voltage of this collector is "locked stable" the effective

bandwidth limiting of the Miller capacitance is greatly

reduced. The signal is then passed through a second fully-

realized differential gain stage and finally through a

proprietary common emitter output stage for improved

rail-to-rail output performance. The result is a highly-stable,

low distortion, low power, and high frequency amplifier

capable of driving moderately capacitive loads with near

rail-to-rail performance.

INPUT OUTPUT RANGE

The three amplifier channels have an input common mode

voltage range from 0.15V below the bottom rail to within

established by the charge pump at negative one half the

positive supply). As the input signal moves outside the

specified range, the output signal will exhibit increasingly

higher levels of harmonic distortion. And of course, as load

resistance becomes lower, the current drive capability of the

device will be challenged and its ability to drive close to each

rail is reduced. For instance, with a load resistance of 1k

Ω

the output swing is within a 100mV of the rails, while a load

resistance of 150

Ω limits the output swing to within around

300mV of the rails.

AMPLIFIER OUTPUT IMPEDANCE

To achieve near rail-to-rail performance, the output stage of

the ISL59833 uses transistors in the common emitter

configuration, typically producing higher output impedance

than the standard emitter follower output stage. The

exceptionally high open loop gain of the ISL59833 and local

feedback reduces output impedance to less than a 2

Ω at low

frequency. However, since output impedance of the device is

exponentially modulated by the magnitude of the open loop

gain, output impedance increases with frequency as the

open loop gain decreases with frequency. This inductive-like

effect of the output impedance is countered in the ISL59833

1

2

3

4

16

15

14

13

5

6

7

12

11

10

8

9

RIN

GIN

BIN

REF

VEE

GND

VEEOUT

DGND

ROUT

GOUT

BOUT

VCC

EN

VCC

NC

DVCC

RED_IN

GREEN_IN

75

Ω

75

Ω

75

Ω

75

Ω

75

Ω

RED_OUT

GREEN_OUT

BLUE_OUT

0.1µF

ENABLE

1

3

2

0.1µF

Option: Panasonic 120

Ω Bead

EXC3BP121H

Lower Amp output noise from charge pump

0.1µF

75

Ω

OFFSET

CONTROL

0.1µF

1k

Ω

499

Ω

ISL59833