전자부품 데이터시트 검색엔진 |
|
GSC2118 데이터시트(PDF) 3 Page - GTM CORPORATION |
|
GSC2118 데이터시트(HTML) 3 Page - GTM CORPORATION |
3 / 7 page GSC2118 Page: 3/7 ISSUED DATE :2006/04/13 REVISED DATE : Ordering Information ( contd. ) Part Number Marking Output Voltage Part Number Marking Output Voltage GSC2118-AD 8AAD2 XXXX Adjustable Detailed Description The GSC2118 of COMS regulator contains a PMOS pass transistor, voltage reference, error amplifier, over- current protection, and thermal shutdown. The P-channel pass transistor receives data from the error amplifier, over-current shutdown, and thermal protection circuits. During normal operation, the error amplifier compares the output voltage to a precision reference. Over-current and Thermal shutdown circuits become active when the junction temperature exceeds 140 : , or the current exceeds 2.2A. During thermal shutdown, the output voltage remains low. Normal operation is restored when the junction temperature drops below 120 : . The GSC2118 behaves like a current source when the load reaches 2.2A. However, if the load impedance drops below 0.3 , the current drops back to 600mA to prevent excessive power dissipation. Normal operation is restored when the load resistance exceeds 0.75 . External Capacitors The GSC2118 is stable with an output capacitance to ground of 4.7 F or greater. Ceramic capacitors have the lowest ESR, and will offer the best AC performance. Conversely, Aluminum Electrolytic capacitors exhibit the highest ESR, resulting in the poorest AC response. Unfortunately, large value ceramic capacitors are comparatively expensive. One option is to parallel a 0.1 F ceramic capacitor with a 10 F Aluminum Electrolytic. The benefit is low ESR, high capacitance, and low overall cost. A second capacitor is recommended between the input and ground to stabilize Vin. The input capacitor should be at least 0.1 F to have a beneficial effect. All capacitors should be placed in close proximity to the pins. A “Quiet” ground termination is desirable. This can be achieved with a “Star” connection. Enable When pulled low, the PMOS pass transistor shuts off, and all internal circuits are powered down. In this state, the quiescent current is less than 1 A. This pin behaves much like an electronic switch. 100k resistor is necessary between VEN source and EN pin when VEN is higher than VIN. (Note: there is no internal pull-up for EN PIN) Adjustable Version The adjustable version uses external feedback resistors to generate an output voltage anywhere from 1.5V to 5.0V. Vadj is trimmed to 1.242V and Vout is given by the equation: VOUT=Vadj * (1+R1/R2) Feedback resistors R1 and R2 should be high enough to keep quiescent current low, but increasing R1+R2 will reduce stability. In general, R1 and R2 in the 10’s of k will produce adequate stability, given reasonable layout precautions. To improve stability characteristics, keep parasitic on the ADJ pin to minimum, and lower R1 and R2 values. |
유사한 부품 번호 - GSC2118 |
|
유사한 설명 - GSC2118 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |