전자부품 데이터시트 검색엔진 |
|
L6920DTR 데이터시트(PDF) 7 Page - STMicroelectronics |
|
L6920DTR 데이터시트(HTML) 7 Page - STMicroelectronics |
7 / 13 page 7/13 L6920 Figure 11. No regulation. Iload > Iload_lim Trace1: Vout (100mV~/div) Trace 4: IL (200mA/div). Time div.: 5 µs/div 4.1 Start-up One of the key features of L6920 is the startup at sup- ply voltage down to 1V (please see the diagram in Figure 5. in case of heavy load). The device leaves the startup mode of operation as soon as VOUT goes over 1.4V. During startup, the synchronous switch is off and the energy is trans- ferred to the load through its intrinsic body diode. The N-channel switches with a very low RDSon thanks to an internal charge pump used to bias the power mos gate. Because of this modified behavior, TON/TOFF times are lengthened. Current limit and zero crossing detection are still available. 4.2 Shutdown In shutdown mode (SHDN pulled low) all internal cir- cuitries are turned off, minimizing the current provid- ed by the battery (ISHDN < 100 nA, in typical case). Both switches are turned off, and the low battery comparator output is forced in high impedance state. The synchronous switch body diode causes a para- sitic path between power supply and output that can't be avoided also in shutdown. 4.3 Low battery detection The L6920 includes a low battery detector compara- tor. Threshold is VREF voltage and a 1.3% hystere- sis is added to avoid oscillations when input crosses the threshold slowly. The LBO is an open drain out- put so a pull up resistor is required for a proper use. 4.4 Reverse polarity A protection circuit has been implemented to avoid that L6920 and the battery are destroyed in case of wrong battery insertion. In addition, this circuit has been designed so that the current required by the battery is zero also in reverse polarity. 5 Application Information 5.1 Output voltage selection Output voltage must be selected acting on FB pin. Three choices are available: fixed 3.3V, 5V or adjust- able output set via an external resistor divider. Table 5. Output Voltage Selection VOUT = 3.3V FB pin connected to OUT (see application circuit) VOUT = 5V FB pin connected to GND 2V ≤ VOUT ≤ 5.2V FB pin connected to a resistive divider V OUT 1.23V 1 R4 R5 -------- + ⎝⎠ ⎛⎞ = |
유사한 부품 번호 - L6920DTR |
|
유사한 설명 - L6920DTR |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |