전자부품 데이터시트 검색엔진 |
|
STA506A 데이터시트(PDF) 8 Page - STMicroelectronics |
|
STA506A 데이터시트(HTML) 8 Page - STMicroelectronics |
8 / 14 page STA506A 8/14 There are two possible modes subsequent to activating a fault: – 1) SHUTDOWN mode: with FAULT (pull-up resistor) and TRI-STATE pins independent, an activated fault will disable the device, signaling low at the FAULT output. The device may subsequently be reset to normal operation by toggling the TRI-STATE pin from High to Low to High using an external logic signal. – 2) AUTOMATIC recovery mode: This is shown in the Application Circuit of fig.1. The FAULT and TRI-STATE pins are shorted together and connected to a time constant circuit com- prising R59 and C58. An activated FAULT will force a reset on the TRI-STATE pin causing normal operation to resume fol- lowing a delay determined by the time constant of the circuit. If the fault condition is still present , the circuit operation will continue repeating until the fault condition is removed . An increase in the time constant of the circuit will produce a longer recovery interval. Care must be taken in the overall system design as not to exceed the protection thesholds under normal operation. 3.3 Power Outputs: The STA506A power and output pins are duplicated to provide a low impedance path for the device's bridged outputs . All duplicate power, ground and output pins must be connected for proper operation. The PWRDN or TRI-STATE pins should be used to set all MOSFETS to the Hi-Z state during power-up until the logic power supply, VL , is settled. 3.4 Parallel Output / High Current Operation: When using DDX Mode output , the STA506A outputs can be connected in parallel in order to increase the output current capability to a load. In this configuration the STA506A can provide 80W into 8 ohm or up to 120W into 4ohm. This mode of operation is enabled with the CONFIG pin (pin.24) connected to Vdd and the inputs combined IN1A=IN1B, IN2A=IN2B and the outputs combined OUT1A=OUT1B, OUT2A=OUT2B. 3.5 Additional Informations: Output Filter: A passive 2nd-order passive filter is used on the STA506A power outputs to reconstruct an analog Audio Signal . System performance can be significantly affected by the output filter design and choice of passive components. A filter design for 6ohm/8ohm loads is shown in the Typical Application circuit of fig.1. Figure 9 shows a filter design suitable for 4ohm loads. Figure 10 shows a filter for ½ bridge mode , 4 ohm loads. 3.6 Power Dissipation & Heat Sink Requirements: The power dissipated within the device will depend primarily on the supply voltage, load impedance and output modulation level. The PowerSO36 package of the STA506A includes an exposed thermal slug on the top of the device to provide a direct thermal path from the IC to the heatsink. Careful consideration must be given to the overall thermal design . See figure 8 for power derating versus Slug temperature using different heatsinks and considering the Rth-jc =1.5°C/W. |
유사한 부품 번호 - STA506A |
|
유사한 설명 - STA506A |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |