전자부품 데이터시트 검색엔진 |
|
TDA7374B 데이터시트(PDF) 8 Page - STMicroelectronics |
|
TDA7374B 데이터시트(HTML) 8 Page - STMicroelectronics |
8 / 13 page Offset Control The quiescent output voltage must be as close as possible to its nominal value, so that less undis- torted power would be available. For this reason an input bias current compensa- tion is implemented to riduce the voltage drop across the input resistors, which appears ampli- fied at the outputs. Gain Internally Fixed to 26dB Advantages of this design choice are in terms of: components and space saving output noise, supply voltage rejection and dis- tortion optimization. Silent Turn On/Off and Muting/Stand-by Func- tion The stand-by can be easily activated by means of a CMOS level applied to pin 7 through a RC filter. Under stand-by condition the device is turned off completely (supply current= 1 µA TYP ; output at- tenuation= 90 dB TYP). Every ON/OFF operation is virtually pop free. Furthermore, at turn-on the device stays in muting condition for a time determined by the value as- signed to the SVR capacitor (T= Csvr * 7,000). While in muting the device outputs becomes in- sensitive to any kinds of signal that may be pre- sent at the input terminals. In other words every transient coming from previous stages produces no unpleasant acoustic effect to the speakers. Another situation under which the device is totally muted is whenever the supply voltage drops lower than 7V. This is helpful to pop suppression during the turn-off by battery switch. BUILT-IN PROTECTION SYSTEMS Full Protection of Device and Loudspeakers Against AC/DC Short Circuits (to Gnd, to Vs, across the Speakers). Reliable and safe operation in presence of all kinds of short circuit involving the outputs is as- sured by a built-in protection system that operates in the following way: In case of overload, a SCR is activated as soon as the current flowing through the output transis- tors overcomes a preset threshold value depend- ing on the chip temperature. The SCR causes an interruption of the supply current of the power transistor. Load Dump Voltage Surge The TDA 7374 has a circuit which enables it to withstand a voltage pulse train on pins 3 and 13, of the type shown in fig. 16. If the supply voltage peaks to more than 50V, then an LC filter must be inserted between the supply and pins 3 and 13, in order to assure that the pulses at pins 3 and 13 will be held within the limits shown. A suggested LC network is shown in fig. 15. With this network, a train of pulses with amplitude up to 120V and width of 2ms can be applied at point A. This type of protection is ON when the supply voltage (pulse or DC) exceeds 18V. For this reason the maximum operating supply volt- age is 18V. Polarity Inversion High current (up to 10A) can be handled by the device with no damage for a longer period than the blow-out time of a quick 2A fuse (normally connected in series with the supply). This fea- tures is added to avoid destruction, if during fitting to the car, a mistake on the connection of the supply is made. Open Ground When the radio is in the ON condition and the ground is accidentally opened, a standard audio amplifier will be damaged. On the TDA7374B pro- tection diodes are included to avoid any damage. Inductive Load A protection diode is provided to allow use of the TDA7374B with inductive loads. Figure 15 Figure 16 TDA7374B 8/13 |
유사한 부품 번호 - TDA7374B |
|
유사한 설명 - TDA7374B |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |