전자부품 데이터시트 검색엔진 |
|
SN74ALVTH32374 데이터시트(PDF) 6 Page - Texas Instruments |
|
SN74ALVTH32374 데이터시트(HTML) 6 Page - Texas Instruments |
6 / 10 page SN54ALVTH32374, SN74ALVTH32374 2.5-V/3.3-V 32-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS SCES280 – SEPTEMBER 1999 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 electrical characteristics over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted) PARAMETER TEST CONDITIONS SN54ALVTH32374 SN74ALVTH32374 UNIT PARAMETER TEST CONDITIONS MIN TYP† MAX MIN TYP† MAX UNIT VIK VCC = 3 V, II = –18 mA –1.2 –1.2 V VCC = 3 V to 3.6 V, IOH = –100 µA VCC–0.2 VCC–0.2 VOH VCC =3V IOH = –24 mA 2 V VCC = 3 V IOH = –32 mA 2 VCC = 3 V to 3.6 V, IOL = 100 µA 0.2 0.2 IOL = 16 mA 0.4 VOL IOL = 24 mA 0.5 V VOL VCC = 3 V IOL = 32 mA 0.5 V IOL = 48 mA 0.55 IOL = 64 mA 0.55 Control inputs VCC = 3.6 V, VI = VCC or GND ±1 ±1 Control inputs VCC = 0 or 3.6 V, VI = 5.5 V 10 10 II VI = 5.5 V 10 10 µA Data inputs VCC = 3.6 V VI = VCC 1 1 VI = 0 –5 –5 Ioff VCC = 0, VI or VO = 0 to 4.5 V ±100 µA IBHL‡ VCC = 3 V, VI = 0.8 V 75 75 µA IBHH§ VCC = 3 V, VI = 2 V –75 –75 µA IBHLO¶ VCC = 3.6 V, VI = 0 to VCC 500 500 µA IBHHO# VCC = 3.6 V, VI = 0 to VCC –500 –500 µA IEX|| VCC = 3 V, VO = 5.5 V 125 125 µA IOZ(PU/PD)k VCC ≤ 1.2 V, VO = 0.5 V to VCC, VI = GND or VCC, OE = don’t care ±100 ±100 µA IOZH VCC = 3.6 V VO = 3 V, VI = 0.8 V or 2 V 5 5 µA IOZL VCC = 3.6 V VO = 0.5 V, VI = 0.8 V or 2 V –5 –5 µA VCC = 3.6 V, Outputs high 0.07 0.1 0.07 0.1 ICC VCC = 3.6 V, IO = 0, Outputs low 3.2 5 3.2 5 mA VI = VCC or GND Outputs disabled 0.07 0.1 0.07 0.1 ∆ICCh VCC = 3 V to 3.6 V, One input at VCC – 0.6 V, Other inputs at VCC or GND 0.4 0.4 mA Ci VCC = 3.3 V, VI = 3.3 V or 0 3.5 3.5 pF Co VCC = 3.3 V, VO = 3.3 V or 0 6 6 pF † All typical values are at VCC = 3.3 V, TA = 25°C. ‡ The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. § The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. ¶ An external driver must source at least IBHLO to switch this node from low to high. # An external driver must sink at least IBHHO to switch this node from high to low. || Current into an output in the high state when VO > VCC kHigh-impedance state during power up or power down hThis is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. |
유사한 부품 번호 - SN74ALVTH32374 |
|
유사한 설명 - SN74ALVTH32374 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |