Notes:

Model

Number

Input

Output

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage (VDC)

Current (mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load

No-Load

I501RU

24

9.0 - 36.0

270

25

5.0

1,000

100

77

700

I502RU

24

9.0 - 36.0

260

25

12.0

420

42

80

700

I503RU

24

9.0 - 36.0

257

25

15.0

333

33

81

700

I504RU

24

9.0 - 36.0

285

25

24.0

200

20

73

700

I505RU

24

9.0 - 36.0

278

25

±5.0

±500

±50

75

700

I506RU

24

9.0 - 36.0

270

25

±12.0

±200

±20

77

700

I507RU

24

9.0 - 36.0

264

25

±15.0

±166

±16

79

700

I508RU

24

9.0 - 36.0

257

25

±24.0

±104

±10

81

700

I511RU

48

18.0 - 72.0

131

20

5.0

1,000

100

79

350

I512RU

48

18.0 - 72.0

127

20

12.0

420

42

82

350

I513RU

48

18.0 - 72.0

122

20

15.0

333

33

85

350

I514RU

48

18.0 - 72.0

121

20

24.0

200

20

86

350

I515RU

48

18.0 - 72.0

139

20

±5.0

±500

±50

75

350

I516RU

48

18.0 - 72.0

133

20

±12.0

±200

±20

78

350

I517RU

48

18.0 - 72.0

127

20

±15.0

±166

±16

82

350

I518RU

48

18.0 - 72.0

122

20

±24.0

±104

±10

85

350

Pin

Single

Dual

Pin

Single

Dual

1

+Vin

+Vin

4

No Pin

Common

2

-Vin

-Vin

5

-Vout

-Vout

3

+Vout

+Vout

Derating Curve

Notes:

1. When measuring output ripple, it is recommended that an external ceramic

capacitor (approx approx 1 µF to 10 µF) be placed from the +Vout pin to the

-Vout pin for single output units and from each output to common for dual

output units.

2. These units should not be operated with a load under 10% of full load. Opera-

tion at no-load

may cause damage to the unit.

3. These converters are specified for operation without external components.

However, in some applications the addition of input/ouput capacitors will

enhance stability and reduce output ripple. Recommended capacitor values

are:

Vin

Input

Capacitor

Vout

Output

Capacitor

24 VDC

100 µF

5 VDC

100 µF

48 VDC

100 µF

12 VDC

100 µF

15 VDC

100 µF

24 VDC

100 µF

For applications requiring very low output noise levels, a simple LC filter should

be effective.

4. Dual output units may be connected to provide

a 10V, 24V, 30V or 48 VDC output. To do this,

connect the load across the positive (+Vout) and

negative (-Vout) outputs and float the output common.

5. It is recommended that a fuse be used on the input

of a power supply for protection. See the Model

Selection table above for the correct rating.

Model Selection Guide

Mechanical Dimensions

Pin Connections

MicroPower Direct

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com