전자부품 데이터시트 검색엔진 |
|
ISL22416WFU10Z 데이터시트(PDF) 4 Page - Intersil Corporation |
|
ISL22416WFU10Z 데이터시트(HTML) 4 Page - Intersil Corporation |
4 / 14 page 4 FN6227.2 September 9, 2009 RESISTOR MODE (Measurements between RW and RL with RH not connected, or between RW and RH with RL not connected) RINL (Note 14) Integral Non-linearity DCP register set between 10 hex and 7F hex; monotonic over all tap positions; W and U option -1 1 MI (Note 11) RDNL (Note 13) Differential Non-linearity W option -1 1 MI (Note 11) U option -0.5 0.5 MI (Note 11) Roffset (Note 12) Offset W option 0 1 5 MI (Note 11) U option 0 0.5 2 MI (Note 11) Analog Specifications Over recommended operating conditions, unless otherwise stated. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN TYP (Note 4) MAX UNIT Operating Specifications Over the recommended operating conditions, unless otherwise specified. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established by characterization and are not production tested. SYMBOL PARAMETER TEST CONDITIONS MIN TYP (Note 4) MAX UNIT ICC1 VCC Supply Current (Volatile Write/Read) fSCK = 5MHz; (for SPI Active, Read and Volatile Write states only) 0.5 mA ICC2 VCC Supply Current (Non-volatile Write/Read) fSCK = 5MHz; (for SPI Active, Read and Non-volatile Write states only) 3mA ISB VCC Current (Standby) VCC = +5.5V @ +85°C, SPI interface in standby state 5µA VCC = +5.5V @ +125°C, SPI interface in standby state 7µA VCC = +3.6V @ +85°C, SPI interface in standby state 3µA VCC = +3.6V @ +125°C, SPI interface in standby state 5µA ISD VCC Current (Shutdown) VCC = +5.5V @ +85°C, SPI interface in standby state 3µA VCC = +5.5V @ +125°C, SPI interface in standby state 5µA VCC = +3.6V @ +85°C, SPI interface in standby state 2µA VCC = +3.6V @ +125°C, SPI interface in standby state 4µA ILkgDig Leakage Current, at Pins SHDN, SCK, SDI, SDO and CS Voltage at pin from GND to VCC, SDO is inactive -1 1 µA tWRT (Note 18) Wiper Response Time Wiper Response Time after SPI write to WR register 1.5 µs tShdnRec (Note 18) DCP Recall Time from Shutdown Mode From rising edge of SHDN signal to wiper stored position and RH connection 1.5 µs SCK rising edge of last bit of ACR data byte to wiper stored position and RH connection 1.5 µs VPOR Power-on Recall Voltage Minimum VCC at which memory recall occurs 2.0 2.6 V VCC Ramp VCC Ramp Rate 0.2 V/ms ISL22416 |
유사한 부품 번호 - ISL22416WFU10Z |
|
유사한 설명 - ISL22416WFU10Z |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |