전자부품 데이터시트 검색엔진 |
|
FAN5403 데이터시트(PDF) 1 Page - Fairchild Semiconductor |
|
FAN5403 데이터시트(HTML) 1 Page - Fairchild Semiconductor |
1 / 37 page September 2011 © 2009 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN5400 Family • Rev. 1.0.7 FAN5400/FAN5401/FAN5402/ FAN5403/ FAN5404/ FAN5405 USB-Compliant Single-Cell Li-Ion Switching Charger with USB-OTG Boost Regulator Features Fully Integrated, High-Efficiency Charger for Single-Cell Li-Ion and Li-Polymer Battery Packs Faster Charging than Linear Charge Voltage Accuracy: 0.5% at 25°C 1% from 0 to 125°C 5% Input Current Regulation Accuracy 5% Charge Current Regulation Accuracy 20V Absolute Maximum Input Voltage 6V Maximum Input Operating Voltage 1.25A Maximum Charge Rate Programmable through High-Speed I2C Interface (3.4Mb/s) with Fast Mode Plus Compatibility – Input Current – Fast-Charge / Termination Current – Charger Voltage – Termination Enable 3MHz Synchronous Buck PWM Controller with Wide Duty Cycle Range Small Footprint 1H External Inductor Safety Timer with Reset Control 1.8V Regulated Output from VBUS for Auxiliary Circuits Weak Input Sources Accommodated by Reducing Charging Current to Maintain Minimum VBUS Voltage Low Reverse Leakage to Prevent Battery Drain to VBUS 5V, 300mA Boost Mode for USB OTG for 2.5 to 4.5V Battery Input Applications Cell Phones, Smart Phones, PDAs Tablet, Portable Media Players Gaming Device, Digital Cameras Description The FAN5400 family (FAN540X) combines a highly integrated switch-mode charger, to minimize single-cell Lithium-ion (Li-ion) charging time from a USB power source, and a boost regulator to power a USB peripheral from the battery. The charging parameters and operating modes are programmable through an I 2C Interface that operates up to 3.4Mbps. The charger and boost regulator circuits switch at 3MHz to minimize the size of external passive components. The FAN540X provides battery charging in three phases: conditioning, constant current, and constant voltage. To ensure USB compliance and minimize charging time, the input current is limited to the value set through the I 2C host. Charge termination is determined by a programmable minimum current level. A safety timer with reset control provides a safety backup for the I 2C host. The integrated circuit (IC) automatically restarts the charge cycle when the battery falls below an internal threshold. If the input source is removed, the IC enters a high-impedance mode with leakage from the battery to the input prevented. Charge status is reported back to the host through the I 2C port. Charge current is reduced when the die temperature reaches 120°C. The FAN540X can operate as a boost regulator on command from the system. The boost regulator includes a soft-start that limits inrush current from the battery. The FAN540X is available in a 1.96 x 1.87mm, 20-bump, 0.4mm pitch WLCSP package. FAN540X SW PGND C OUT L1 VBAT + Battery CSIN R SENSE 68m 1 H C BAT SYSTEM LOAD 0.1 F VBUS 1 F PMID 4.7 F SDA SCL OTG/USB# C REG 1 F VREG STAT 10 F DISABLE C BUS C MID Figure 1. Typical Application (FAN5403-05 Pin Out) All trademarks are the property of their respective owners. |
유사한 부품 번호 - FAN5403 |
|
유사한 설명 - FAN5403 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |