전자부품 데이터시트 검색엔진 |
|
DAC08EQ 데이터시트(PDF) 9 Page - Analog Devices |
|
DAC08EQ 데이터시트(HTML) 9 Page - Analog Devices |
9 / 12 page DAC08 –9– REV. A APPLICATIONS INFORMATION REFERENCE AMPLIFIER SET-UP The DAC08 is a multiplying D/A converter in which the output current is the product of a digital number and the input refer- ence current. The reference current may be fixed or may vary from nearly zero to +4.0 mA. The full-scale output current is a linear function of the reference current and is given by: IFR = 255 256 × I REF, where IREF = I14. In positive reference applications, an external positive reference voltage forces current through R14 into the VREF(+) terminal (pin 14) of the reference amplifier. Alternatively, a negative ref- erence may be applied to VREF(–) at pin 15; reference current flows from ground through R14 into VREF(+) as in the positive reference case. This negative reference connection has the ad- vantage of a very high impedance presented at pin 15. The volt- age at pin 14 is equal to and tracks the voltage at pin 15 due to the high gain of the internal reference amplifier. R15 (nominally equal to R14) is used to cancel bias current errors; R15 may be eliminated with only a minor increase in error. Bipolar references may be accommodated by offsetting VREF or pin 15. The negative common-mode range of the reference am- plifier is given by: VCM– = V– plus (IREF × 1 kΩ) plus 2.5 V. The positive common-mode range is V+ less 1.5 V. When a dc reference is used, a reference bypass capacitor is rec- ommended. A 5.0 V TTL logic supply is not recommended as a reference. If a regulated power supply is used as a reference, R14 should be split into two resistors with the junction bypassed to ground with a 0.1 µF capacitor. For most applications the tight relationship between IREF and IFS will eliminate the need for trimming IREF. If required, full-scale trimming may be accomplished by adjusting the value of R14, or by using a potentiometer for R14. An improved method of full-scale trimming which eliminates potentiometer T.C. effects is shown in the recommended full-scale adjustment circuit. Using lower values of reference current reduces negative power supply current and increases reference amplifier negative common- mode range. The recommended range for operation with a dc reference current is +0.2 mA to +4.0 mA. Figure 27. Negative Low Impedance Output Operation Figure 26. Positive Low Impedance Output Operation Figure 28. Interfacing With Various Logic Families |
유사한 부품 번호 - DAC08EQ |
|
유사한 설명 - DAC08EQ |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |