전자부품 데이터시트 검색엔진 |
|
SN74V263-10PZA 데이터시트(PDF) 8 Page - Texas Instruments |
|
SN74V263-10PZA 데이터시트(HTML) 8 Page - Texas Instruments |
8 / 52 page SN74V263, SN74V273, SN74V283, SN74V293 8192 × 18, 16384 × 18, 32768 × 18, 65536 × 18 3.3-V CMOS FIRST-IN, FIRST-OUT MEMORIES SCAS669D – JUNE 2001 – REVISED FEBRUARY 2003 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 Terminal Functions (Continued) TERMINAL I/O DESCRIPTION NAME I/O DESCRIPTION PFM I Programmable-flag mode. During master reset, a low on PFM selects asynchronous programmable-flag timing mode. A high on PFM selects synchronous programmable-flag timing mode. PRS I Partial reset. PRS initializes the read and write pointers to zero and sets the output register to all zeroes. During partial reset, the existing mode (standard or FWFT), programming method (serial or parallel), and programmable-flag settings, input and output bus widths, big/little endian, interspersed parity select, and retransmit mode are all retained. Q0–Q17 O Data outputs. Data outputs for a 18- or 9-bit bus. When in 18-bit mode, Q0–Q17 are used and when in 9-bit mode, Q0–Q8 are used, and the unused outputs, Q9–Q17 should not be connected. Outputs are not 5-V tolerant regardless of the state of OE. RCLK I Read clock. When enabled by REN, the rising edge of RCLK reads data from the FIFO memory and offsets from the programmable registers. REN I Read enable. REN enables RCLK for reading data from the FIFO memory and offset registers. RM I Retransmit latency mode. During master reset, a low on RM selects zero-latency retransmit timing mode. A high on RM selects normal-latency mode. RT I Retransmit. RT asserted on the rising edge of RCLK initializes the READ pointer to zero, sets the EF flag to low (OR to high in FWFT mode) and does not disturb the write pointer, programming method, existing timing mode, or programmable flag settings. RT is useful to reread data starting from the first physical location of the FIFO. SEN I Serial enable. SEN enables serial loading of programmable flag offsets. WCLK I Write clock. When enabled by WEN, the rising edge of WCLK writes data into the FIFO and offsets into the programmable registers for parallel programming and, when enabled by SEN, the rising edge of WCLK writes one bit of data into the programmable register for serial programming. WEN I Write enable. WEN enables WCLK for writing data into the FIFO memory and offset registers. detailed description inputs data in (D0–Dn) Data inputs for 18-bit-wide data (D0–D17) or data inputs for 9-bit wide data (D0–D8). controls master reset (MRS) A master reset is accomplished when the MRS input is taken to a low state. This operation sets the internal read and write pointers to the first location of the RAM array. PAE goes low, PAF goes high, and HF goes high. If FWFT/SI is high, the FWFT mode, along with IR and OR, is selected. OR goes high and IR goes low. If FWFT/SI is low during master reset, the standard mode, along with EF and FF, is selected. EF goes low and FF goes high. All control settings, such as OW, IW, BE, RM, PFM, and IP, are defined during the master reset cycle. During a master reset, the output register is initialized to all zeroes. A master reset is required after power up, before a write operation can take place. MRS is asynchronous. See Figure 5 for timing information. |
유사한 부품 번호 - SN74V263-10PZA |
|
유사한 설명 - SN74V263-10PZA |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |