전자부품 데이터시트 검색엔진 |
|
FCBN510QE2C10 데이터시트(PDF) 3 Page - Finisar Corporation. |
|
FCBN510QE2C10 데이터시트(HTML) 3 Page - Finisar Corporation. |
3 / 12 page FCBG510QE2Cxx PRELIMINARY Product Specification – July 2014 F i n i s a r Finisar Corporation – 22-Jul-14 Rev A4 Page 3 25 Rx4p Receiver Non-Inverted Data Output 26 GND Ground 1 27 ModPrsL Module Present 28 IntL Interrupt 29 Vcc Tx +3.3 V Power supply transmitter 30 Vcc1 +3.3 V Power Supply 31 LPMode Low Power Mode 32 GND Ground 1 33 Tx3p Transmitter Non-Inverted Data Input 34 Tx3n Transmitter Inverted Data Input 35 GND Ground 1 36 Tx1p Transmitter Non-Inverted Data Input 37 Tx1n Transmitter Inverted Data Input 38 GND Ground 1 Notes 1. Circuit ground is internally isolated from chassis ground. b. SFP+ ends Pin Symbol Name/Description Ref. 1 VEET Transmitter Ground (Common with Receiver Ground) 1 2 TFAULT Transmitter Fault. 2 3 TDIS Transmitter Disable. Laser output disabled on high or open. 3 4 SDA 2-wire Serial Interface Data Line 4 5 SCL 2-wire Serial Interface Clock Line 4 6 MOD_ABS Module Absent. Grounded within the module 4 7 RS0 No connection required 8 RX_LOS Loss of Signal indication. Logic 0 indicates normal operation. 5 9 RS1 No connection required 10 VEER Receiver Ground (Common with Transmitter Ground) 1 11 VEER Receiver Ground (Common with Transmitter Ground) 1 12 RD- Receiver Inverted DATA out. AC Coupled 13 RD+ Receiver Non-inverted DATA out. AC Coupled 14 VEER Receiver Ground (Common with Transmitter Ground) 1 15 VCCR Receiver Power Supply 16 VCCT Transmitter Power Supply 17 VEET Transmitter Ground (Common with Receiver Ground) 1 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled. 20 VEET Transmitter Ground (Common with Receiver Ground) 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. T FAULT is an open collector/drain output, which is pulled up with a 4.7k – 10k Ohms resistor on the host board, but is grounded inside the SFP+ cable plug. 3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 4. Should be pulled up with 4.7k – 10k on host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in. 5. LOS is open collector output. Should be pulled up with 4.7k – 10k on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. |
유사한 부품 번호 - FCBN510QE2C10 |
|
유사한 설명 - FCBN510QE2C10 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |