전자부품 데이터시트 검색엔진 |
|
TC90A53N 데이터시트(PDF) 7 Page - Toshiba Semiconductor |
|
TC90A53N 데이터시트(HTML) 7 Page - Toshiba Semiconductor |
7 / 17 page TC90A53N/F 2001-02-08 7/17 DESCRIPTION OF FUNCTIONS (1) CLAMP (Input clamp) Circuit used to Sync tip clamp composite signal. Apply feedback clamp so that at Y / C separation, the minimum data value after A / D conversion is the internally-fixed level. (2) ADC (A / D converter) High-speed series-parallel 8-bit A / D converter (Dynamic Range: 2.0V). Input composite video signal with amplitude of 1.5 Vp-p (sync to white 100%). (3) 1 H memory Line memory consisting of DRAM for 1 H delay. Two line memories configure a 3-line comb filter. Because the system clock is 4 fsc (14.3 MHz), 910 clocks / 1 H is set. (4) VENH (Vertical enhancer circuit) After coring (2LSB) the non-correlation component among the three lines of the luminance signal, this block enhances the vertical outline. The enhance amount can be selected from three settings : large (+1.25), medium (+0.75), and small (+0.25). The vertical enhance amount is added to the luminous signal obtained by subtracting the color signal from the composite signal, then the luminous signal is output via the D / A converter. Note that if the luminous signal is lower than the pedestal level (internally-fixed value), the vertical enhance amount is not added to. (5) BPF (Horizontal bandpass filter) Uses fsc as the center frequency. Filters the composite signal delayed by 0 H, 1 H, or 2 H and extracts the color signal. The bandpass filter for outputting the color signal at a later stage can be switched on or off to select output of a narrow- or wide-band color signal. (6) DCF (Vertical dynamic comb filter) Vertical bandpass filter which extracts the color signal by detecting vertical non-correlation. Using Toshiba logic, determines the correlation among three lines. If no correlation, determines as the luminous signal and suppresses output of the color signal. (7) 1-line color dot interference reducer circuit Improves color dot interference on a screen where only 1 line has color so that the C signal is processed as the Y signal. Extracts 1-line color dot component and the result is added to the output from the dynamic comb filter. (8) RTIM (Clock / memory timing generator) This block supplies × 4 fsc (14.3 MHz) obtained using the VCO via a buffer to the blocks and generates the timing signal necessary for memory. (9) PLL (× 4 clock generator) Multiplies fsc (3.58 MHz) by 4 and generates system clock 4 fsc (14.3 MHz). (10) DAC (D / A converter) High-speed 8-bit D / A converter. The output amplitudes are : Y output of 1.5 V p-p (typ.) and C output at burst level of 572 mV p-p (typ.). (11) Color killer circuit When the input video signal is a monochrome image, this circuit enables effective use of the luminance signal information regardless of whether there is a burst signal. It does this by preventing the chroma signal output from the comb filter from being subtracted from the luminance signal. While the VBI signal is active it is better not to use the comb function. Setting the KILLER pin to High at this time enables the use of character multiplex and other signals from the Y output unchanged. But since Vertical edge enhancement does not become OFF, be careful when using with Vertical edge enhancement. |
유사한 부품 번호 - TC90A53N |
|
유사한 설명 - TC90A53N |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |