전자부품 데이터시트 검색엔진 |
|
FPV1006-150-R 데이터시트(PDF) 5 Page - Vicor Corporation |
|
FPV1006-150-R 데이터시트(HTML) 5 Page - Vicor Corporation |
5 / 30 page Cool-Power® Rev 1.3 vicorpower.com Page 5 of 30 12/2015 800 927.9474 PI34xx-00 PGD VS1 Block 4 VIN Block 3 PGND Block 2 SGND ADJ TRK SDA SCL ADR0 ADR1 K J H G F E D C B A 13 12 5 4 3 1 14 210 9 8 7 611 SGND Block 1 VOUT Block 5 Package Pin-Out Pin Description Block 1: B2-4, C2-4, D2-3, E2-3, F1-3, G2-3, H2-3, J1-3, K1-2 Block 2: A8-10, B8-10, C8-10, D8-10, E4-10, F4-10, G4-10, H4-10, J4-10, K6-10 Block 3: G12-14, H12-14, J12-14, K12-14 Block 4: A12-14, B12-14, C12-14, D12-14, E12-14, Block 5: A6-7, B6-7, C6-7, D6-7 Name Location Description SGND Block 1 Signal ground: Internal logic ground for EA, TRK, SYNCI, SYNCO and ADJ. SGND and PGND are star connected within the regulator package. PGND Block 2 Power ground: VIN and VOUT power returns. VIN Block 3 Input voltage: and sense for UVLO, OVLO and feed forward ramp. VOUT Block 5 Output voltage: and sense for power switches and feed-forward ramp. VS1 Block 4 Switching node: and ZVS sense for power switches. PGD A1 Parallel Good: Used for parallel timing management intended for lead regulator. EAO A2 Error amp output: External connection for additional compensation and current sharing. EN A3 Enable Input: Regulator enable control. Asserted high or left floating – regulator enabled; Asserted low, regulator output disabled. REM A5 Remote Sense: High side connection. Connect to output regulation point. ADJ B1 Adjust input: An external resistor may be connected between ADJ pin and SGND or VOUT to trim the output voltage up or down. TRK C1 Soft-start and track input: An external capacitor may be connected between TRK pin and SGND to decrease the rate of rise during soft-start. NC K3, A4 No Connect: Leave pins floating. SYNCO K4 Synchronization output: Outputs a high signal for ½ of the minimum period for synchronization of other regulators. SYNCI K5 Synchronization input: Synchronize to the falling edge of external clock frequency. SYNCI is a high impedance digital input node and should always be connected to SGND when not in use. SDA D1 Data Line: Connect to SGND. Factory use only. Not for use in application. SCL E1 Clock Line: Connect to SGND. Factory use only. Not for use in application. ADR1 H1 Tri-state Address: No connect. Factory use only. Not for use in application. ADR0 G1 Tri-state Address: No connect. Factory use only. Not for use in application. |
유사한 부품 번호 - FPV1006-150-R |
|
유사한 설명 - FPV1006-150-R |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |