전자부품 데이터시트 검색엔진
  Korean  ▼
ALLDATASHEET.CO.KR

X  

LM2593HVT-3.3 데이터시트(PDF) 9 Page - National Semiconductor (TI)

[Old version datasheet] Texas Instruments acquired National semiconductor.
부품명 LM2593HVT-3.3
상세설명  SIMPLE SWITCHER Power Converter 150 kHz 2A Step-Down Voltage Regulator, with Features
Download  21 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
제조업체  NSC [National Semiconductor (TI)]
홈페이지  http://www.national.com
Logo NSC - National Semiconductor (TI)

LM2593HVT-3.3 데이터시트(HTML) 9 Page - National Semiconductor (TI)

Back Button LM2593HVT-3.3 Datasheet HTML 5Page - National Semiconductor (TI) LM2593HVT-3.3 Datasheet HTML 6Page - National Semiconductor (TI) LM2593HVT-3.3 Datasheet HTML 7Page - National Semiconductor (TI) LM2593HVT-3.3 Datasheet HTML 8Page - National Semiconductor (TI) LM2593HVT-3.3 Datasheet HTML 9Page - National Semiconductor (TI) LM2593HVT-3.3 Datasheet HTML 10Page - National Semiconductor (TI) LM2593HVT-3.3 Datasheet HTML 11Page - National Semiconductor (TI) LM2593HVT-3.3 Datasheet HTML 12Page - National Semiconductor (TI) LM2593HVT-3.3 Datasheet HTML 13Page - National Semiconductor (TI) Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 21 page
background image
Block Diagram
10133330
PIN FUNCTIONS
+V
IN (Pin 1) — This is the positive input supply for the IC
switching regulator. A suitable input bypass capacitor must
be present at this pin to minimize voltage transients and to
supply the switching currents needed by the regulator.
Output (Pin 2) — Internal switch. The voltage at this pin
switches between approximately (+V
IN −VSAT) and approxi-
mately −0.5V, with a duty cycle of V
OUT/VIN.
Error Flag (Pin 3) — Open collector output that goes active
low (
≤ 1.0V) when the output of the switching regulator is out
of regulation (less than 95% of its nominal value). In this
state it can sink maximum 3mA. When not low, it can be
pulled high to signal that the output of the regulator is in
regulation (power good). During power-up, it can be pro-
grammed to go high after a certain delay as set by the Delay
pin (Pin 5). The maximum rating of this pin should not be
exceeded, so if the rail to which it will be pulled-up to is
higher than 45V, a resistive divider must be used instead of
a single pull-up resistor, as indicated in
Figure 1.
Ground (Pin 4) — Circuit ground.
Delay (Pin 5) — This sets a programmable power-up delay
from the moment that the output reaches regulation, to the
high signal output (power good) on Pin 3. A capacitor on this
pin starts charging up by means on an internal () 3 µA)
current source when the regulated output rises to within 5%
of its nominal value. Pin 3 goes high (with an external
pull-up) when the voltage on the capacitor on Pin 5 exceeds
1.3V. The voltage on this pin is clamped internally to about
1.7V. If the regulated output drops out of regulation (less
than 95% of its nominal value), the capacitor on Pin 5 is
rapidly discharged internally and Pin 3 will be forced low in
about 1/1000
th of the set power-up delay time.
Feedback (Pin 6) — Senses the regulated output voltage to
complete the feedback loop. This pin is directly connected to
the Output for the fixed voltage versions, but is set to 1.23V
by means of a resistive divider from the output for the
Adjustable version. If a feedforward capacitor is used (Ad-
justable version), then a negative voltage spike is generated
on this pin whenever the output is shorted. This happens
because the feedforward capacitor cannot discharge fast
enough, and since one end of it is dragged to Ground, the
other end goes momentarily negative. To prevent the energy
rating of this pin from being exceeded, a small-signal Schot-
tky diode to Ground is recommended for DC input voltages
above 40V whenever a feedforward capacitor is present
(See
Figure 1). Feedforward capacitor values larger than 0.1
µF are not recommended for the same reason, whatever be
the DC input voltage.
Shutdown /Soft-start (Pin 7) — The regulator is in shut-
down mode, drawing about 90 µA, when this pin is driven to
a low level (
≤ 0.6V), and is in normal operation when this Pin
is left floating (internal pull-up) or driven to a high level (
2.0V). The typical value of the threshold is 1.3V and the pin
is internally clamped to a maximum of about 7V. If it is driven
higher than the clamp voltage, it must be ensured by means
of an external resistor that the current into the pin does not
exceed 1mA. The duty cycle is minimum (0%) if this Pin is
below 1.8V, and increases as the voltage on the pin is
increased. The maximum duty cycle (100%) occurs when
this pin is at 2.8V or higher. So adding a capacitor to this pin
produces a softstart feature. An internal current source will
charge the capacitor from zero to its internally clamped
value. The charging current is about 5 µA when the pin is
below 1.3V but is reduced to only 1.6 µA above 1.3V, so as
to allow the use of smaller softstart capacitors.
www.national.com
9


유사한 부품 번호 - LM2593HVT-3.3

제조업체부품명데이터시트상세설명
logo
Texas Instruments
LM2593HVT-5.0/NOPB TI1-LM2593HVT-5.0/NOPB Datasheet
1Mb / 31P
[Old version datasheet]   SIMPLE SWITCHER Power Converter 150-kHz, 2-A Step-Down Voltage Regulator
LM2593HVT-ADJ/NOPB TI1-LM2593HVT-ADJ/NOPB Datasheet
1Mb / 31P
[Old version datasheet]   SIMPLE SWITCHER Power Converter 150-kHz, 2-A Step-Down Voltage Regulator
More results

유사한 설명 - LM2593HVT-3.3

제조업체부품명데이터시트상세설명
logo
National Semiconductor ...
LM2592HV NSC-LM2592HV Datasheet
655Kb / 20P
   SIMPLE SWITCHER Power Converter 150 kHz 2A Step-Down Voltage Regulator
LM2597 NSC-LM2597 Datasheet
900Kb / 34P
   SIMPLE SWITCHER Power Converter 150 kHz 0.5A Step-Down Voltage Regulator, with Features
LM2590HV NSC-LM2590HV Datasheet
752Kb / 20P
   SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator, with Features
LM2598 NSC-LM2598 Datasheet
847Kb / 33P
   SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator, with Features
LM2599 NSC-LM2599 Datasheet
812Kb / 31P
   SIMPLE SWITCHER Power Converter 150 kHz 3A Step-Down Voltage Regulator, with Features
logo
Texas Instruments
LM2598 TI1-LM2598 Datasheet
2Mb / 47P
[Old version datasheet]   SIMPLE SWITCHER Power Converter 150-kHz 1-A Step-Down Voltage Regulator, With Features
LM2592HVT-33 TI-LM2592HVT-33 Datasheet
2Mb / 29P
[Old version datasheet]   LM2592HV SIMPLE SWITCHER Power Converter 150 kHz 2A Step-Down Voltage
LM2597HVM-ADJ TI-LM2597HVM-ADJ Datasheet
2Mb / 48P
[Old version datasheet]   LM2597/LM2597HV SIMPLE SWITCHER Power Converter 150 kHz 0.5A Step-Down Voltage Regulator, with Features
logo
National Semiconductor ...
LM2591HV NSC-LM2591HV Datasheet
730Kb / 20P
   SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator
LM2595 NSC-LM2595 Datasheet
935Kb / 29P
   SIMPLE SWITCHER Power Converter 150 kHz 1A Step-Down Voltage Regulator
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21


데이터시트 다운로드

Go To PDF Page


링크 URL




개인정보취급방침
ALLDATASHEET.CO.KR
ALLDATASHEET 가 귀하에 도움이 되셨나요?  [ DONATE ] 

Alldatasheet는?   |   광고문의   |   운영자에게 연락하기   |   개인정보취급방침   |   링크교환   |   제조사별 검색
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com