전자부품 데이터시트 검색엔진 |
|
LM4765 데이터시트(PDF) 3 Page - National Semiconductor (TI) |
|
|
LM4765 데이터시트(HTML) 3 Page - National Semiconductor (TI) |
3 / 15 page Electrical Characteristics (Notes 4, 5) (Continued) The following specifications apply for V CC = +28V, VEE = −28V with RL = 8Ω unless otherwise specified. Limits apply for TA = 25˚C. Symbol Parameter Conditions LM4765 Units (Limits) Typical Limit (Note 9) (Note 10) GBWP Gain Bandwidth Product f O = 100 kHz, VIN = 50 mVrms 7.5 5 MHz (min) e IN Input Noise IHF — A Weighting Filter 2.0 8 µV (max) (Note 3) R IN = 600Ω (Input Referred) SNR Signal-to-Noise Ratio P O = 1W, A — Weighted, 98 dB Measured at 1 kHz, R S = 25Ω P O = 25W, A — Weighted 108 dB Measured at 1 kHz, R S = 25Ω A M Mute Attenuation Pin 6,11 at 2.5V 115 80 dB (min) Standby Pin V IL Standby Low Input Voltage Not in Standby Mode 0.8 V (max) V IH Standby High Input Voltage In Standby Mode 2.0 2.5 V (min) Mute pin V IL Mute Low Input Voltage Outputs Not Muted 0.8 V (max) V IH Mute High Input Voltage Outputs Muted 2.0 2.5 V (min) Note 1: Operation is guaranteed up to 64V, however, distortion may be introduced from SPiKe Protection Circuitry if proper thermal considerations are not taken into account. Refer to the Application Information section for a complete explanation. Note 2: DC Electrical Test; Refer to Test Circuit #1. Note 3: AC Electrical Test; Refer to Test Circuit #2. Note 4: All voltages are measured with respect to the GND pins (5, 10), unless otherwise specified. Note 5: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is func- tional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guar- antee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 6: For operating at case temperatures above 25˚C, the device must be derated based on a 150˚C maximum junction temperature and a thermal resistance of θJC = 1˚C/W for the T package. Refer to the section Determining the Correct Heat Sink in the Application Information section. Note 7: Human body model, 100 pF discharged through a 1.5 k Ω resistor. Note 8: The operating junction temperature maximum is 150˚C, however, the instantaneous Safe Operating Area temperature is 250˚C. Note 9: Typicals are measured at 25˚C and represent the parametric norm. Note 10: Limits are guarantees that all parts are tested in production to meet the stated values. Note 11: VEE must have at least −9V at its pin with reference to ground in order for the under-voltage protection circuitry to be disabled. In addition, the voltage dif- ferential between VCC and VEE must be greater than 14V. Note 12: The output dropout voltage, VOD, is the supply voltage minus the clipping voltage. Refer to the Clipping Voltage vs. Supply Voltage graph in the Typical Per- formance Characteristics section. www.national.com 3 |
유사한 부품 번호 - LM4765 |
|
유사한 설명 - LM4765 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |