ADE7754AR datasheet(8/44 Pages) AD

부품명	ADE7754AR

상세설명	Poly-phase Multi-Function Energy Metering IC with Serial Port

Download	44 Pages

Scroll/Zoom	100%

제조업체	AD [Analog Devices]

홈페이지	http://www.analog.com

Logo

8 / 44 page

REV. PrG 01/03

PRELIMINARY TECHNICAL DATA

ADE7754

– 8 –

PIN FUNCTION DESCRIPTION

Pin No.

MNEMONIC

DESCRIPTION

1

C F

Calibration Frequency logic output. The CF logic output gives Active Power informa-

tion. This output is intended to be used for operational and calibration purposes. The

full-scale output frequency can be scaled by writing to the CFNUM and CFDEN reg-

isters—see Energy To Frequency Conversion.

2

DGND

This provides the ground reference for the digital circuitry in the ADE7754, i.e. multi-

plier, filters and digital-to-frequency converter. Because the digital return currents in

the ADE7754 are small, it is acceptable to connect this pin to the analog ground plane

of the whole system. However high bus capacitance on the DOUT pin may result in

noisy digital current which could affect performance.

3

DV DD

Digital power supply. This pin provides the supply voltage for the digital circuitry in

the ADE7754. The supply voltage should be maintained at 5V ± 5% for specified op-

eration. This pin should be decoupled to DGND with a 10µF capacitor in parallel with

a ceramic 100nF capacitor.

4AVDD

Analog power supply. This pin provides the supply voltage for the analog circuitry in

the ADE7754. The supply should be maintained at 5V ± 5% for specified operation.

Every effort should be made to minimize power supply ripple and noise at this pin by

the use of proper decoupling. The typical performance graphs in this data sheet show

the power supply rejection performance. This pin should be decoupled to AGND with a

10µF capacitor in parallel with a ceramic 100nF capacitor.

5,6;

IAP, IAN;

Analog inputs for current channel. This channel is intended for use with the current

7,8;

IBP, IBN;

transducer and is referenced in this document as the current channel. These inputs are

9,10

ICP, ICN

fully differential voltage inputs with maximum differential input signal levels of ±0.5V,

±0.25V and ±0.125V, depending on the gain selections of the internal PGA -See Analog

Inputs.

All inputs have internal ESD protection circuitry, and in addition an overvoltage of

±6V can be sustained on these inputs without risk of permanent damage.

11

AGND

This pin provides the ground reference for the analog circuitry in the ADE7754, i.e.

ADCs, temperature sensor, and reference. This pin should be tied to the analog ground

plane or the quietest ground reference in the system. This quiet ground reference

should be used for all analog circuitry, e.g. anti aliasing filters, current and voltage

transducers etc. In order to keep ground noise around the ADE7754 to a minimum, the

quiet ground plane should only connected to the digital ground plane at one point. It is

acceptable to place the entire device on the analog ground plane.

12

REFIN/OUT

This pin provides access to the on-chip voltage reference. The on-chip reference has a

nominal value of 2.4V ± 8% and a typical temperature coefficient of 30ppm/°C. An

external reference source may also be connected at this pin. In either case this pin

should be decoupled to AGND with a 1µF ceramic capacitor.

13, 14

VN, VCP,

Analog inputs for the voltage channel. This channel is intended for use with the voltage

15, 16

VBP, VAP

transducer and is referenced as the voltage channel in this document. These inputs are

single-ended voltage inputs with maximum signal level of ±0.5V with respect to VN for

specified operation. These inputs are voltage inputs with maximum differential input

signal levels of ±0.5V, ±0.25V and ±0.125V, depending on the gain selections of the

internal PGA - see Analog Inputs.

All inputs have internal ESD protection circuitry, and in addition an over voltage of

±6V can be sustained on these inputs without risk of permanent damage.

17

RESET

Reset pin for the ADE7754. A logic low on this pin will hold the ADCs and digital

circuitry (including the Serial Interface) in a reset condition.

18

IRQ

Interrupt Request Output. This is an active low open drain logic output. Maskable

interrupts include: Active Energy Register at half level, Apparent Energy Register at

half level, and waveform sampling up to 26kSPS. See ADE7754 Interrupts.

유사한 부품 번호 - ADE7754AR

제조업체	부품명	데이터시트	상세설명
Analog Devices	ADE7754AR	2Mb / 44P	ADE7754
Analog Devices	ADE7754ARRL	2Mb / 44P	ADE7754

More results

유사한 설명 - ADE7754AR

제조업체	부품명	데이터시트	상세설명
Analog Devices	ADE7758	1Mb / 68P	Poly Phase Multifunction Energy Metering IC with Per Phase Information REV. A
Analog Devices	ADE7758	979Kb / 72P	Poly Phase Multifunction Energy Metering IC with Per Phase Information Rev. E
Integrated Device Techn...	90E32	877Kb / 71P	Poly-Phase High-Performance Wide-Span Energy Metering IC
Integrated Device Techn...	90E36	1,005Kb / 79P	Poly-Phase High-Performance Wide-Span Energy Metering IC
Analog Devices	ADE7754	530Kb / 44P	Polyphase Multifunction Energy Metering IC with Serial Port REV. 0
Analog Devices	ADE7858	1Mb / 76P	Poly Phase Multifunction Energy Metering IC with per Phase Active and Reactive Powers Rev. PrA
ATMEL Corporation	M90E36A	998Kb / 87P	Enhanced Poly-Phase High-Performance Wide-Span Energy Metering IC
ATMEL Corporation	ATM90E32AS	789Kb / 84P	Enhanced Poly-Phase High-Performance Wide-Span Energy Metering IC
Sames	SA9103C	251Kb / 16P	SINGLE PHASE BIDIRECTIONAL POWER/ENERGY METERING IC WITH SERIAL INTERFACE
Analog Devices	ADE7756	797Kb / 32P	Active Energy Metering IC with Serial Interface REV. 0

More results

ADE7754AR 데이터시트(PDF) 8 Page - Analog Devices

ADE7754AR 데이터시트(HTML) 8 Page - Analog Devices

유사한 부품 번호 - ADE7754AR

유사한 설명 - ADE7754AR

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44

데이터시트 다운로드

링크 URL