전자부품 데이터시트 검색엔진 |
|
DS1855 데이터시트(PDF) 2 Page - Dallas Semiconductor |
|
DS1855 데이터시트(HTML) 2 Page - Dallas Semiconductor |
2 / 20 page DS1855 2 of 20 PIN DESCRIPTIONS Name TSSOP BGA Description VCC 14 A3 Power Supply Terminal. The DS1855 will support supply voltages ranging from +2.7V to +5.5V. GND 7 D1 Ground Terminal. SDA 1 B2 2-Wire serial data interface. The serial data pin is for serial data transfer to and from the DS1855. The pin is open drain and may be wire-ORed with other open drain or open collector interfaces. SCL 2 A2 2-Wire Serial Clock Input. The serial clock input is used to clock data into the DS1855 on rising edges and clock data out on falling edges. WP 6 C1 Write Protect Input. If set to logic 0, the data in memory and the potentiometer wiper setting may be changed. If set to logic 1, both the memory and the potentiometer wiper settings will be write protected. The WP pin is pulled high internally. A0 3 A1 Address Input. Pins A0, A1, and A2 are used to specify the address of each DS1855 when used in a multi-dropped configuration. Up to eight DS1855s may be addressed on a single 2-wire bus. A1 4 B1 Address Input. A2 5 C2 Address Input. H0 13 A4 High terminal of Potentiometer 0. For both potentiometers, it is not required that the high terminal be connected to a potential greater than the low terminal. Voltage applied to the high terminal of each potentiometer cannot exceed VCC or go below ground. H1 11 B3 High terminal of Potentiometer 1. L0 8 D3 Low terminal of Potentiometer 0. For both potentiometers, it is not required that the low terminal be connected to a potential less than the high terminal. Voltage applied to the low terminal of each potentiometer cannot exceed VCC or go below ground. L1 10 C4 Low terminal of Potentiometer 1. W0 9 D4 Wiper terminal of Pot 0. The wiper position of Potentiometer 0 is determined by the byte at EEPROM memory location F9h. Voltage applied to the wiper terminal of each potentiometer cannot exceed the power supply voltage, VCC, or go below ground. W1 12 B4 Wiper terminal of Pot 1. The wiper position of Potentiometer 1 is determined by the byte at EEPROM memory location F8h. NC C3 No Connect. NC D2 No Connect. |
유사한 부품 번호 - DS1855 |
|
유사한 설명 - DS1855 |
|
|
링크 URL |
개인정보취급방침 |
ALLDATASHEET.CO.KR |
ALLDATASHEET 가 귀하에 도움이 되셨나요? [ DONATE ] |
Alldatasheet는? | 광고문의 | 운영자에게 연락하기 | 개인정보취급방침 | 링크교환 | 제조사별 검색 All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |